WAGO 285-416 Protective Warning Marker 5/card Terminal Block Colour Yellow. Pack size 50.

• Manufacturer part No. 285-416
• Colour Yellow
• Contents 50pk
• Weight 1.453g

WAGO 285-420 Protective Warning Marker 5/card Colour Yellow. Pack size 100.

• Manufacturer part No. 285-420
• Colour Yellow
• Contents 100pk
• Weight 0.43g

WAGO 285-421 Finger Guard Cover Colour Yellow. Pack size 100.

• Manufacturer part No. 285-421
• Colour Yellow
• Contents 100pk
• Weight 0.67g

Power tap from the WAGO 285 series suitable for use with 35mm² high current terminal blocks.

• Width 8mm
• Current rating 32A
• Connection points: 1
• Colour: grey
• Manufacturer's part 285-427

Insulated step down jumper from the WAGO 285 series, suitable for use with TOPJOB®S terminal blocks.

• Rated voltage 800V
• Rated current 90A
• Colour: grey
• Manufacturer's part 285-430

WAGO 285-440 Protective Warning Marker 5/card Colour Yellow. Pack size 50.

• Manufacturer part No. 285-440
• Colour Yellow
• Contents 50pk
• Weight 2g

WAGO 285-441 Finger Guard Cover Colour Yellow. Pack size 100.

• Manufacturer part No. 285-441
• Colour Yellow
• Contents 100pk
• Weight 2.01g

WAGO 285-442 5mm wide. Carrier for Power Cage Clamp 35/50/95 Colour Grey. Pack size 1.

• Manufacturer part No. 285-442
• Colour Grey
• Contents 1pk

Power tap from the WAGO 285 series suitable for use with 50mm² high current terminal blocks.

• Width 16mm
• Current rating 41A
• Connection points: 2
• Colour: grey
• Manufacturer's part 285-447

Empty 2-pole housing from WAGO with 2 levels and 2 jumper slots.

• Pre-assembled unit
• Flexible conductor termination
• Customisation of connection levels
• Sealable, transparent cover
• Push-in CAGE CLAMP® connection
• Pitch 5mm
• Height 107mm
• Width 12.5mm
• Depth 108mm
• Manufacturer's part 2857-101

Empty 2-pole housing from WAGO with 3 levels and 2 jumper slots.

• Pre-assembled unit
• Flexible conductor termination
• Customisation of connection levels
• Sealable transparent cover
• Push-in CAGE CLAMP® connection
• Pitch 5mm
• Height 107mm
• Width 12.5mm
• Depth 110mm
• Manufacturer's part 2857-102

Empty 2-pole housing from WAGO with 3 levels.

• Pre-assembled unit
• Flexible conductor termination
• Customisation of connection levels
• Sealable, transparent cover
• Push-in CAGE CLAMP® connection
• Pitch 5mm
• Height 107mm
• Width 12.5mm
• Depth 112mm
• Manufacturer's part 2857-103

Empty 4-pole housing from WAGO with 2 levels and 4 jumper slots.

• Pre-assembled unit
• Flexible conductor termination
• Customisation of connection levels
• Sealable transparent cover
• Push-in CAGE CLAMP® connection
• Pitch 5mm
• Height 107mm
• Width 22.5mm
• Depth 108mm
• Manufacturer's part 2857-121

Empty 4-pole housing from WAGO with 3 levels and 2 jumper slots.

• Pre-assembled unit
• Flexible conductor termination
• Customisation of connection levels
• Sealable transparent cover
• Push-in CAGE CLAMP® connection
• Pitch 5mm
• Height 107mm
• Width 22.5mm
• Depth 110mm
• Manufacturer's part 2857-122

Empty 4-pole housing from WAGO with 3 levels.

• Pre-assembled unit
• Flexible conductor termination
• Customisation of connection levels
• Sealable transparent cover
• Push-in CAGE CLAMP® connection
• Pitch 5mm
• Height 107mm
• Width 22.5mm
• Depth 112mm
• Manufacturer's part 2857-123

Empty 4-pole housing from WAGO with 1 level and 4 jumper slots.

• Pre-assembled unit
• Flexible conductor termination
• Customisation of connection levels
• Sealable transparent cover
• Push-in CAGE CLAMP® connection
• Pitch 5mm
• Height 107mm
• Width 22.5mm
• Depth 105mm
• Manufacturer's part 2857-124

Stripboard from WAGO with 2-2 connection levels.

• Manufacturer's part 2857-191/3140-000

Stripboard from WAGO with 3-2 connection levels.

• Manufacturer's part 2857-192/3140-000

Stripboard from WAGO with 3-3 connection levels.

• Manufacturer's part 2857-193/3140-000

Stripboard from WAGO with 1-1 connection levels.

• Manufacturer's part 2857-194/3140-000

Pluggable relay module from WAGO suitable for use with carrier terminal blocks.

• Colour: grey
• Height 82.5mm
• Width 10mm
• Manufacturer's part 286-364

Switching module from WAGO with changeover rocker switch.

• Switching voltage 250V
• Switching current 6A
• Colour: grey
• Width 15mm
• Manufacturer's part 286-895

Mounting carrier from WAGO suitable for screw or DIN-35 rail mounting.

• Colour: grey
• Height 26.5mm
• Width 45.5mm
• Depth 65.5mm
• Manufacturer's part 288-001

Universal snap-fit mounting foot from WAGO suitable for use with DIN 15, 32 and 35 rails.

• Colour: grey
• Width 45.5mm
• Depth 65.5mm
• Manufacturer's part 288-002

Mounting carrier for PCBs from WAGO suitable for Europa card (100 x 160mm).

• Colour: grey
• Height 25mm
• Width 162mm
• Depth 105mm
• Manufacturer's part 288-003

Small lateral cover from WAGO suitable for DIN-35 rail mounting.

• Size 1
• Colour: grey
• Width 6.35mm
• Depth 85mm
• Manufacturer's part 288-601

Fixing foot from WAGO suitable for DIN-35 rail mounting.

• Colour: grey
• Height 25.2mm
• Width 85mm
• Depth 12.7mm
• Manufacturer's part 288-602

Small lateral cover from WAGO suitable for DIN-35 rail mounting.

• Size 2
• Colour: grey
• Width 8.75mm
• Depth 106mm
• Manufacturer's part 288-621

Fixing foot from WAGO suitable for DIN-35 rail mounting.

• Colour: grey
• Height 25.2mm
• Width 106mm
• Depth 17.55mm
• Manufacturer's part 288-622

Component module with 8 diodes from the WAGO 289 series.

• CAGE CLAMP® connection
• Height 31.5mm
• Width 47mm
• Depth 65.5mm
• Manufacturer's part 289-101

Self-assembly module from the WAGO 289 series, suitable for DIN-rail mounting with 2 x 8 drilled holes.

The CAGE CLAMP® connection technique allows stripped solid and ferruled conductors to be pushed in. With its space saving design, the terminal block is up to 30% smaller than standard terminal blocks and with a conductor entry angle of less than 15° allows easier installation in smaller spaces.

• Dimensions 42.5 x 32 x 62.5mm
• Manufacturer's part 289-103

Self-assembly module from the WAGO 289 series, suitable for DIN-rail mounting with 2 x 8 drilled holes.

The CAGE CLAMP® connection technique allows stripped solid and ferruled conductors to be pushed in. With its space saving design, the terminal block is up to 30% smaller than standard terminal blocks and with a conductor entry angle of less than 15° allows easier installation in smaller spaces.

• Dimensions 47 x 31.5 x 65.5mm
• Manufacturer's part 289-103

Diode gate module from the WAGO 289 series, suitable for DIN-rail mounting.

The CAGE CLAMP® connection technique allows stripped solid and ferruled conductors to be pushed in. With its space saving design, the terminal block is up to 30% smaller than standard terminal blocks and with a conductor entry angle of less than 15° allows easier installation in smaller spaces.

• Manufacturer's part 289-105

Component module with 14 diodes from the WAGO 289 series.

• CAGE CLAMP® connection
• Height 31.5mm
• Width 47mm
• Depth 65.5mm
• Manufacturer's part 289-111

Resistor gate with 8 2K2 resistors from the WAGO 289 series.

• CAGE CLAMP® connection
• Height 31.5mm
• Width 47mm
• Depth 65.5mm
• Manufacturer's part 289-113

Resistor gate with 8 2K7 resistors from the WAGO 289 series.

• CAGE CLAMP® connection
• Height 31.5mm
• Width 47mm
• Depth 65.5mm
• Manufacturer's part 289-114

This module for populating from the WAGO 289 series is suitable for DIN-rail mounting and has 2 x 8 soldering points.

The CAGE CLAMP® connection technique allows stripped solid and ferruled conductors to be pushed in. With its space saving design, the terminal block is up to 30% smaller than standard terminal blocks and with a conductor entry angle of less than 15° allows easier installation in smaller spaces.

• Manufacturer's part 289-131

Component module with 20 diodes from the WAGO 289 series.

• CAGE CLAMP® connection
• Height 21mm
• Width 69mm
• Depth 50mm
• Manufacturer's part 289-151

The WAGO Interface Module for Ethernet RJ-45 with shield-clamp - mounting base TS35.

• Manufacturer's part: 289-172

The WAGO Interface Module for Ethernet RJ-45 with shield area for WAGO shield clamping saddle. Terminals with Cage Clamp® (WAGO Series 739) 0.08-1.5 mm²/AWG 28-14.

The CAGE CLAMP® connection technique allows stripped solid and ferruled conductors to be pushed in. With their space saving design, the terminal block is up to 30% smaller than standard terminal block and with a conductor entry angle of less than 15° which allows easier installation in smaller spaces.

• Grey colour
• CAGE CLAMP®S Connection
• Manufacturer's part: 289-175

The WAGO Interface Module for Ethernet Y-Conjack 22 is a high quality shielded Y-Con connector ideal for crossover cables.

• Standards/regulations ISO/IEC 11801: 2002- 09; EN 55022
• Connection cable MinCAT5
• Max Transfer length 100m
• Min1000 mating cycles
• Manufacturer's part: 289-177

A 12-pole interface module from WAGO with male connectors according to DIN 41651.

• CAGE CLAMP® connection
• DIN-35 rail mounting
• Height (above DIN rail) 28mm
• Width 66.5mm
• Depth 63.5mm
• Manufacturer's part 289-404

The WAGO Interface Module for DIN 41612 Connector 0.08-2.5mm² with 64-pole male connector Type C for female connector with IDC connection. Vertical plug-in direction, mounting base for TS35.

The CAGE CLAMP® connection technique allows stripped solid and ferruled conductors to be pushed in. With their space saving design, the terminal block is up to 30% smaller than standard terminal block and with a conductor entry angle of less than 15° which allows easier installation in smaller spaces.

• Manufacturer type description: 289-522
• CAGE CLAMP®S Connection
• 171 x 34 x 85mm (W x H x D)

The WAGO D-SUB Pin Strip Interface Module 0.08-2.5mm² is a high quality module with sub miniature 37-pole D-type male connector for mating connectors with IDC mating (vertical direction). Mounting base for TS35.

The CAGE CLAMP® connection technique allows stripped solid and ferruled conductors to be pushed in. With their space saving design, the terminal block is up to 30% smaller than standard terminal block and with a conductor entry angle of less than 15° which allows easier installation in smaller spaces.

• Manufacturer type description: 289-543
• Vertical plug-in
• CAGE CLAMP®S Connection

The WAGO D-SUB Pin Strip Interface Module 0.08-2.5mm² is a high quality module with sub miniature 25-pole D-type male connector for mating connectors with solder connection (vertical direction). Mounting base for TS35.

The CAGE CLAMP® connection technique allows stripped solid and ferruled conductors to be pushed in. With their space saving design, the terminal block is up to 30% smaller than standard terminal block and with a conductor entry angle of less than 15° which allows easier installation in smaller spaces.

• Manufacturer type description: 0289-0547
• Vertical plug-in
• CAGE CLAMP®S Connection

The WAGO D-SUB Pin Strip Interface Module 0.08-2.5mm² is a high quality module with sub miniature 37-pole D-type female connector for mating connectors with IDC mating (vertical direction). Mounting base for TS35.

The CAGE CLAMP® connection technique allows stripped solid and ferruled conductors to be pushed in. With their space saving design, the terminal block is up to 30% smaller than standard terminal block and with a conductor entry angle of less than 15° which allows easier installation in smaller spaces.

• Manufacturer type description: 289-553
• Vertical plug-in
• CAGE CLAMP®S Connection

The WAGO D-SUB Pin Strip Interface Module 0.08-2.5mm² is a high quality module with sub miniature 15-pole D-type female connector for mating connectors with solder connection (vertical direction). Mounting base for TS35.

The CAGE CLAMP® connection technique allows stripped solid and ferruled conductors to be pushed in. With their space saving design, the terminal block is up to 30% smaller than standard terminal block and with a conductor entry angle of less than 15° which allows easier installation in smaller spaces.

• Manufacturer type description: 0289-0556
• Vertical plug-in
• CAGE CLAMP®S Connection

The WAGO D-SUB 37-Pin Interface Module with sub miniature 37-pole D-type female connector for mating plug with soldered joint, shield connection and vertical plug-in direction.

The CAGE CLAMP® connection technique allows stripped solid and ferruled conductors to be pushed in. With their space saving design, the terminal block is up to 30% smaller than standard terminal block and with a conductor entry angle of less than 15° which allows easier installation in smaller spaces.

• Manufacturer type description: 0289-0578
• Vertical plug-in
• CAGE CLAMP®S connection

Connection module from WAGO suitable for 8 3-conductor sensors.

• CAGE CLAMP® connection
• Height above DIN rail 34mm
• Width 56mm
• Depth 85mm
• Manufacturer's part 289-664

Connection module from WAGO with LED indicator suitable for 8 3-conductor sensors.

• CAGE CLAMP® connection
• Positive switching
• Height above DIN rail 34mm
• Width 56mm
• Depth 105mm
• Manufacturer's part 289-665