An ABB aluminium side operated Fireman's switch, that is 2-pole, and a power rating of 25A. You can often see these switches on the outside wall of shops, industrial or commercial buildings for disconnection and isolation purposes. They are used by firemen to turn off neon lighting or other hazardous electrical equipment when attending a fire at the premises. The enclosure and handle are painted red, to make it easy to spot. The On and Off positions are clearly indicated on the front side with 'I' and 'O'.

The operating handle is designed in such a way that a fireman's hook or axe can be used to switch it off. To reset, a so called 'two hands grip' must be used. The interlocking mechanism prevents accidental manoeuvres. Delivery includes PE+ neutral terminal and membrane glands (IP54) /sealing plugs. For IP65 degree of protection compression glands must be used.

• 25A @ 400V
• Robust and reliable design in non flammable material (Aluminium)
• Operating handle locked in 'O' position and a two hands grip to reset for safety reasons
• Easy to install and to operate. Possible to add on an auxiliary contact
• Supplied in red
• Complies with IEC 60947-3 and BS7671
• ABB type; KSF225 DP
• ABB part; 2CMA142435R1000
• Supplied in 2-pole version

An ABB aluminium side operated Fireman's switch, that is 3-pole, and a power rating of 25A. You can often see these switches on the outside wall of shops, industrial or commercial buildings for disconnection and isolation purposes. They are used by firemen to turn off neon lighting or other hazardous electrical equipment when attending a fire at the premises. The enclosure and handle are painted red, to make it easy to spot. The On and Off positions are clearly indicated on the front side with 'I' and 'O'.

The operating handle is designed in such a way that a fireman's hook or axe can be used to switch it off. To reset, a so called 'two hands grip' must be used. The interlocking mechanism prevents accidental manoeuvres. Delivery includes PE+ neutral terminal and membrane glands (IP54) /sealing plugs. For IP65 degree of protection compression glands must be used.

• 25A @ 400V
• Robust and reliable design in non flammable material (Aluminium)
• Operating handle locked in 'O' position and a two hands grip to reset for safety reasons
• Easy to install and to operate. Possible to add on an auxiliary contact
• Supplied in red
• Complies with IEC 60947-3 and BS7671
• ABB type; KSF325 TPN
• ABB part; 2CMA142436R1000
• Supplied in 3-pole version

An ABB aluminium side operated Fireman's switch, that is 4-pole, and a power rating of 25A. You can often see these switches on the outside wall of shops, industrial or commercial buildings for disconnection and isolation purposes. They are used by firemen to turn off neon lighting or other hazardous electrical equipment when attending a fire at the premises. The enclosure and handle are painted red, to make it easy to spot. The On and Off positions are clearly indicated on the front side with 'I' and 'O'.

The operating handle is designed in such a way that a fireman's hook or axe can be used to switch it off. To reset, a so called 'two hands grip' must be used. The interlocking mechanism prevents accidental manoeuvres. Delivery includes PE+ neutral terminal and membrane glands (IP54) /sealing plugs. For IP65 degree of protection compression glands must be used.

• 25A @ 400V
• Robust and reliable design in non flammable material (Aluminium)
• Operating handle locked in 'O' position and a two hands grip to reset for safety reasons
• Easy to install and to operate. Possible to add on an auxiliary contact
• Supplied in red
• Complies with IEC 60947-3 and BS7671
• ABB type; KSF425 TPSN
• ABB part; 2CMA142437R1000
• Supplied in 4-pole version

An ABB aluminium side operated Fireman's switch, that is 3-pole, and a power rating of 40A. You can often see these switches on the outside wall of shops, industrial or commercial buildings for disconnection and isolation purposes. They are used by firemen to turn off neon lighting or other hazardous electrical equipment when attending a fire at the premises. The enclosure and handle are painted red, to make it easy to spot. The On and Off positions are clearly indicated on the front side with 'I' and 'O'.

The operating handle is designed in such a way that a fireman's hook or axe can be used to switch it off. To reset, a so called 'two hands grip' must be used. The interlocking mechanism prevents accidental manoeuvres. Delivery includes PE+ neutral terminal and membrane glands (IP54) /sealing plugs. For IP65 degree of protection compression glands must be used.

• 40A @ 400V
• Robust and reliable design in non flammable material (Aluminium)
• Operating handle locked in 'O' position and a two hands grip to reset for safety reasons
• Easy to install and to operate. Possible to add on an auxiliary contact
• Supplied in red
• Complies with IEC 60947-3 and BS7671
• ABB type; KSF340 TPN
• ABB part; 2CMA142438R1000
• Supplied in 3-pole version

BACO 3-pole 25A circuit breaker with double isolation per phase and reversible terminals.

• Safety switch to disconnect and isolate poles
• Dimensions (W x H): 44 x 75.4mm
• Double break type load switching
• Red padlockable handle
• Yellow plate
• Conforms to IEC EN 60947-3
• Manufacturer's part 172001

This contact block with metal mounting plate is ideal for use with 22mm pushbutton switches. The contact block is supplied in green in Normally Open (NO) position.

• For Use with: 22mm Diameter Control Switches
• No. of Poles of Poles: 1
• Contact Current Max: 10A
• Contact Voltage AC Max: 400V
• Contact Voltage DC Max: 250V
• Switch Terminals: Screw
• CamdenBoss part CC10B

Rapid is an official distributor of CamdenBoss products. The products listed here are those that Rapid hold in stock – but we have access to many more, including the company's complete range of terminal blocks. Click here to make an enquiry about ordering CamdenBoss terminal blocks, connectors and enclosures.

This CamdenBoss 40mm Emergency Stop button, has been designed for failsafe operation on machinery. Once pushed, the button can only be released by turning the key. This adds more security to restart machinery as it requires a deliberate action by an operator.

• Metal bodied
• Rated 600V, 10A max AC
• Operating frequency 3,600 per hour
• Panels mount 1-6mm thick
• Positive opening operation
• Conform to IEC 947-5-1 and EN 60947-5-1
• Terminal marking to EN 50013
• Supplied in red

Rapid is an official distributor of CamdenBoss products. The products listed here are those that Rapid hold in stock – but we have access to many more, including the company's complete range of terminal blocks. Click here to make an enquiry about ordering CamdenBoss terminal blocks, connectors and enclosures.

This flush metal bodied pushbutton switch is from the CamdenBoss CCTTR30 range. It has a diameter of 22mm diameter, making it ideal for applications including control stations, instrumentation panels and industrial machines.

• Flush metal bodied control push-buttons
• Rated 600V, 10A max AC
• Operating frequency 3,600 per hour
• Panels mount 1-6mm thick
• Positive opening operation
• Conform to IEC 947-5-1 and EN 60947-5-1
• Terminal marking to EN 50013
• Supplied in black

Rapid is an official distributor of CamdenBoss products. The products listed here are those that Rapid hold in stock – but we have access to many more, including the company's complete range of terminal blocks. Click here to make an enquiry about ordering CamdenBoss terminal blocks, connectors and enclosures.

This flush metal bodied pushbutton switch is from the CamdenBoss CCTTR30 range. It has a diameter of 22mm diameter, making it ideal for applications including control stations, instrumentation panels and industrial machines.

• Flush metal bodied control push-buttons
• Rated 600V, 10A max AC
• Operating frequency 3,600 per hour
• Panels mount 1-6mm thick
• Positive opening operation
• Conform to IEC 947-5-1 and EN 60947-5-1
• Terminal marking to EN 50013
• Supplied in green

Rapid is an official distributor of CamdenBoss products. The products listed here are those that Rapid hold in stock – but we have access to many more, including the company's complete range of terminal blocks. Click here to make an enquiry about ordering CamdenBoss terminal blocks, connectors and enclosures.

This flush metal bodied pushbutton switch is from the CamdenBoss CCTTR30 range. It has a diameter of 22mm diameter, making it ideal for applications including control stations, instrumentation panels and industrial machines.

• Flush metal bodied control push-buttons
• Rated 600V, 10A max AC
• Operating frequency 3,600 per hour
• Panels mount 1-6mm thick
• Positive opening operation
• Conform to IEC 947-5-1 and EN 60947-5-1
• Terminal marking to EN 50013
• Supplied in red

Rapid is an official distributor of CamdenBoss products. The products listed here are those that Rapid hold in stock – but we have access to many more, including the company's complete range of terminal blocks. Click here to make an enquiry about ordering CamdenBoss terminal blocks, connectors and enclosures.

This flush metal bodied pushbutton switch is from the CamdenBoss CCTTR30 range. It has a diameter of 22mm diameter, making it ideal for applications including control stations, instrumentation panels and industrial machines.

• Flush metal bodied control push-buttons
• Rated 600V, 10A max AC
• Operating frequency 3,600 per hour
• Panels mount 1-6mm thick
• Positive opening operation
• Conform to IEC 947-5-1 and EN 60947-5-1
• Terminal marking to EN 50013
• Supplied in yellow

Rapid is an official distributor of CamdenBoss products. The products listed here are those that Rapid hold in stock – but we have access to many more, including the company's complete range of terminal blocks. Click here to make an enquiry about ordering CamdenBoss terminal blocks, connectors and enclosures.

A flush metal bodied pushbutton switch with a white horizontal legend clearly marked on a black background. The CamdenBoss CCTTRAHBK is 22mm in diameter, and ideally suited to applications including control stations, instrumentation panels and industrial machines.

• Flush metal bodied control push-buttons
• Rated 600V, 10A max AC
• Operating frequency 3,600 per hour
• Panels mount 1-6mm thick
• Positive opening operation
• Conform to IEC 947-5-1 and EN 60947-5-1
• Terminal marking to EN 50013
• Supplied in horizontal arrow style

Rapid is an official distributor of CamdenBoss products. The products listed here are those that Rapid hold in stock – but we have access to many more, including the company's complete range of terminal blocks. Click here to make an enquiry about ordering CamdenBoss terminal blocks, connectors and enclosures.

This CamdenBoss 2-pole selector switch is in the style of Maintained Left and Right. It has a diameter of 22mm diameter, making it ideal for applications including control stations, instrumentation panels and industrial machines.

• Metal bodied
• Rated 600V, 10A max AC
• Operating frequency 3,600 per hour
• Panels mount 1-6mm thick
• Positive opening operation
• Conform to IEC 947-5-1 and EN 60947-5-1
• Terminal marking to EN 50013
• Supplied in black
• Supplied in 2-pole Maintained Left and Right style
• CamdenBoss part CCTTSS211

Rapid is an official distributor of CamdenBoss products. The products listed here are those that Rapid hold in stock – but we have access to many more, including the company's complete range of terminal blocks. Click here to make an enquiry about ordering CamdenBoss terminal blocks, connectors and enclosures.

This CamdenBoss 3-pole selector switch is in the style of Return to Centre from Left to Right. It has a diameter of 22mm diameter, making it ideal for applications including control stations, instrumentation panels and industrial machines.

• Metal bodied
• Rated 600V, 10A max AC
• Operating frequency 3,600 per hour
• Panels mount 1-6mm thick
• Positive opening operation
• Conform to IEC 947-5-1 and EN 60947-5-1
• Terminal marking to EN 50013
• Supplied in black
• Supplied in 3-pole Return to Centre from Left to Right
• CamdenBoss part CCTTSS300

Rapid is an official distributor of CamdenBoss products. The products listed here are those that Rapid hold in stock – but we have access to many more, including the company's complete range of terminal blocks. Click here to make an enquiry about ordering CamdenBoss terminal blocks, connectors and enclosures.

A CamdenBoss 2-pole selector switch from the CSC1 range. The CSC1-70 is an assembled E-Stop, supplied in a metal body with a key operated selector switch. The switch is supplied in the Maintained Left and Right option and is ideally suited to applications including control stations, instrumentation panels and industrial machines.

• Assembled selector switch box
• 1NC Contact
• Metal bodied (yellow)
• Rated 600V, 10A max AC
• Conform to IEC 947-5-1 & EN 60947-5-1
• CE Approved
• Supplied in the Maintained Left and Right option
• CamdenBoss part CSC1-70

Rapid is an official distributor of CamdenBoss products. The products listed here are those that Rapid hold in stock – but we have access to many more, including the company's complete range of terminal blocks. Click here to make an enquiry about ordering CamdenBoss terminal blocks, connectors and enclosures.

The EMAS PV3E30B2 Emergency Stop, Crane Pendant is a 3 hole, single and double speed crane pendant. With an aesthetic look and ergonomic usage, this pendant station has assistance of ABS reinforced material with a mechanical interlock.

• Product: Crane Pendant Station
• Type: 3 Hole
• Contact: 1NC
• Current (Ie): 4A (250V AC)
• Usage Category: AC15
• Mechanical Life (Min Qty): 1000000
• Electrical Life (Min Qty): 100000
• Operating Frequency (On-Off/Hour): Mech. 900 Elec. 900
• Insulation Voltage (Ui): 300 V
• Impulse Withstand Voltage (Uimp): 2.5 kV
• Dielectric Strength (Body-Contact): 2.500V AC
• Dielectric Strength (Contact-Contact): 1.500V AC
• Isolation Resistance: 10 MΩ (500 V DC)
• Operating Temperature: -15 / + 80 °C
• Pollution Degree: 3
• Protection Degree: IP65
• Contact Material: AgNi
• Cable Section: 1.5-2.5 mm2
• Screw Torque: 1.5Nm
• Short: PV Series
• Speed: Single Speed
• 1. Hole: Emergency Stop

The EMAS PV3E30B4 Emergency Stop, Crane Pendant is an optional double and single speed, 2 hole emergency stop crane pendant. With an aesthetic look and ergonomic usage, this crane pendant station has assistance of ABS reinforced material with a mechanical interlock.

• Product: Crane Pendant Station
• Type: 3 Hole
• Contact: 1NC
• Current (Ie): 4A (250V AC)
• Usage Category: AC15
• Mechanical Life (Min Qty): 1000000
• Electrical Life (Min Qty): 100000
• Operating Frequency (On-Off/Hour): Mech. 900 Elec. 900
• Insulation Voltage (Ui): 300 V
• Impulse Withstand Voltage (Uimp): 2.5 kV
• Dielectric Strength (Body-Contact): 2.500V AC
• Dielectric Strength (Contact-Contact): 1.500V AC
• Isolation Resistance: 10 MΩ (500 V DC)
• Operating Temperature: -15 / + 80 °C
• Pollution Degree: 3
• Protection Degree: IP65
• Contact Material: AgNi
• Cable Section: 1.5-2.5 mm2
• Screw Torque: 1.5Nm
• Short Circuit Breaking Capacity (Ics): 1kA
• Serial: PV Series
• Speed: Double Speed
• 1. Hole: Emergency Stop

The EMAS PV5E30B22 Crane Pendant is a optional single or double speed, PV series, 5 hole emergency stop crane pendant. With an aesthetic look and ergonomic usage, this crane pendant station has assistance of ABS reinforced material with a mechanical interlock.

• Product: Crane Pendant Station
• Type: 5 Hole
• Contact: 1NC
• Current (Ie): 4A (250V AC)
• Usage Category: AC15
• Mechanical Life (Min Qty): 1000000
• Electrical Life (Min Qty): 100000
• Operating Frequency (On-Off/Hour): Mech. 900 Elec. 900
• Insulation Voltage (Ui): 300 V
• Impulse Withstand Voltage (Uimp): 2.5 kV
• Dielectric Strength (Body-Contact): 2.500V AC
• Dielectric Strength (Contact-Contact): 1.500V AC
• Isolation Resistance: 10 MΩ (500 V DC)
• Operating Temperature: -15 / + 80 °C
• Pollution Degree: 3
• Protection Degree: IP65
• Contact Material: AgNi
• Cable Section: 1.5-2.5 mm2
• Screw Torque: 1.5Nm
• Short Circuit Breaking Capacity (Ics): 1kA
• Serial: PV Series
• Speed: Single Speed
• 1. Hole: Emergency Stop

The EMAS PV5E30B44 Emergency Stop, Crane Pendant Station is an optional single or double speed, PV series, 5 hole crane pendant. With an aesthetic look and ergonomic usage, this crane pendant station has assistance of ABS reinforced material with a mechanical interlock.

• Product: Crane Pendant Station
• Type: 5 Hole
• Contact: 1NC
• Current (Ie): 4A (250V AC)
• Usage Category: AC15
• Mechanical Life (Min Qty): 100000
• Electrical Life (Min Qty): 100000
• Operating Frequency (On-Off/Hour): Mech. 900 Elec. 900
• Insulation Voltage (Ui): 300 V
• Impulse Withstand Voltage (Uimp): 2.5 kV
• Dielectric Strength (Body-Contact): 2.500V AC
• Dielectric Strength (Contact-Contact): 1.500V AC
• Isolation Resistance: 10 MΩ (500 V DC)
• Operating Temperature: -15 / + 80 °C
• Pollution Degree: 3
• Protection Degree: IP65
• Contact Material: AgNi
• Cable Section: 1.5-2.5 mm2
• Screw Torque: 1.5Nm
• Short Circuit Breaking Capacity (Ics): 1kA
• Serial: PV Series
• Speed: Double Speed
• 1. Hole: Emergency Stop

A 100A rated isolator with a 3-pole + switched neutral configuration. The isolator has a rotary switch and an IP65 rated ABS enclosure. This isolator is ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 270 x 215 x 122mm
• Early make/late break neutral contact
• Switched neutral contacts in blue for identification
• Insulated enclosure
• Easy access and switch removal
• Flame retardant material
• 20 or 25mm knock-outs (depending on rating)
• Padlockable for security
• All switch ratings at AC-21
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 100A isolator with a 4-pole configuration. The isolator has a rotary switch and metal clad enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 270 x 215 x 125mm
• Epoxy coated steel enclosure
• Lid RAL 7032, back box RAL 7043
• Easy access and switch removal
• Padlockable for security
• IP54 Rated
• All switch ratings at AC-21
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 125A rated isolator with a 3-pole + switched neutral configuration. The isolator has a rotary switch and an IP65 rated ABS enclosure. This isolator is ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 270 x 215 x 122mm
• Early make/late break neutral contact
• Switched neutral contacts in blue for identification
• Insulated enclosure
• Easy access and switch removal
• Flame retardant material
• 20 or 25mm knock-outs (depending on rating)
• Padlockable for security
• All switch ratings at AC-21
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 125A isolator with a 6-pole configuration. The isolator has a rotary switch and steel enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 400 x 300 x 200mm
• Epoxy coated strong steel
• Bottom gland plate
• Colour RAL 7035
• Easy access and switch removal
• Padlockable for security
• All switch ratings at AC-22
• Room in enclosure to add 1x extra auxiliary block either side of the switch
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 125A isolator with an 8-pole configuration. The isolator has a rotary switch and steel enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 400 x 300 x 200mm
• Epoxy coated strong steel
• Bottom gland plate
• Colour RAL 7035
• Easy access and switch removal
• Padlockable for security
• All switch ratings at AC-22
• Room in enclosure to add 1x extra auxiliary block either side of the switch
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 20A rated isolator with a 3-pole + switched neutral configuration. The isolator has a rotary switch and an IP65 rated ABS enclosure. This isolator is ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 125 x 100 x 74mm
• Early make/late break neutral contact
• Switched neutral contacts in blue for identification
• Insulated enclosure
• Easy access and switch removal
• Flame retardant material
• 20 or 25mm knock-outs (depending on rating)
• Padlockable for security
• All switch ratings at AC-21
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

This 125A main pole contact is designed for use with door interlocked and boxed isolator switch units when an additional pole is required. The contact may be fitted either side of the switch.

• Easily connected
• Rear mounting
• All switch ratings AC-22
• CB, CE, SEMKO, UL508, IEC and EN 60947-3

A 25A isolator with a 4-pole configuration. The isolator has a rotary switch and an IP65 rated ABS enclosure. The larger than average enclosure makes the unit ideal for SWA cabling and also gives room for an extra auxiliary.

• Dimensions (H x W x D) 175 x 125 x 90mm
• Die Cast aluminium enclosure
• Lid RAL 7032, back box RAL 7043
• Easy access and switch removal
• Padlockable for security
• All switch ratings at AC-21
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 25A isolator with a 6-pole configuration. The isolator has a rotary switch and insulated enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 280 x 190 x 130mm
• 25mm Knock-outs
• Easy access and switch removal
• Padlockable for security
• Flame retardant material
• All switch ratings at AC-22
• Room in enclosure to add 1x extra auxiliary block either side of the switch
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 25A isolator with an 8-pole configuration. The isolator has a rotary switch and insulated enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 280 x 190 x 130mm
• 25mm Knock-outs
• Easy access and switch removal
• Padlockable for security
• Flame retardant material
• All switch ratings at AC-22
• Room in enclosure to add 1x extra auxiliary block either side of the switch
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

This 25 to 63A main pole contact is designed for use with door interlocked and boxed isolator switch units when an additional pole is required. The contact may be fitted either side of the switch.

• Easily connected
• Rear mounting
• All switch ratings AC-22
• CB, CE, SEMKO, UL508, IEC and EN 60947-3

This 80A main pole contact is designed for use with door interlocked and boxed isolator switch units when an additional pole is required. The contact may be fitted either side of the switch.

• Easily connected
• Rear mounting
• All switch ratings AC-22
• CB, CE, SEMKO, UL508, IEC and EN 60947-3

A 32A isolator with a 4-pole configuration. The isolator has a rotary switch and an IP65 rated ABS enclosure. The larger than average enclosure makes the unit ideal for SWA cabling and also gives room for an extra auxiliary.

• Dimensions (H x W x D) 175 x 125 x 90mm
• Die Cast aluminium enclosure
• Lid RAL 7032, back box RAL 7043
• Easy access and switch removal
• Padlockable for security
• All switch ratings at AC-21
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 25A isolator with a 4-pole configuration. The isolator has a rotary switchand stainless steel enclosure. Particularly suitable for pharmaceutical and food preparation areas.

• Dimensions (H x W x D) 173 x 100 x 120mm
• Grade 304 brushed stainless steel
• Fully earth bonded
• Easy access and switch removal
• Padlockable for security
• All switch ratings at AC-22
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 32A isolator with a 4-pole configuration. The isolator has a rotary switch and metal clad enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 220 x 145 x 90mm
• Epoxy coated steel enclosure
• Lid RAL 7032, back box RAL 7043
• Easy access and switch removal
• Padlockable for security
• IP54 Rated
• All switch ratings at AC-21
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 32A isolator with an 8-pole configuration. The isolator has a rotary switch and insulated enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 280 x 190 x 130mm
• 25mm Knock-outs
• Easy access and switch removal
• Padlockable for security
• Flame retardant material
• All switch ratings at AC-22
• Room in enclosure to add 1x extra auxiliary block either side of the switch
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 40A rated 3-pole isolator with a rotary switch in an IP65 rated ABS enclosure. This isolator is ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 125 x 100 x 74mm
• Easy access and switch removal
• Flame retardant material
• 20mm knock-outs
• Padlockable for security
• All switch rating at AC-21
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 40A isolator with a 4-pole configuration. The isolator has a rotary switch and an IP65 rated ABS enclosure. The larger than average enclosure makes the unit ideal for SWA cabling and also gives room for an extra auxiliary.

• Dimensions (H x W x D) 175 x 125 x 90mm
• Die Cast aluminium enclosure
• Lid RAL 7032, back box RAL 7043
• Easy access and switch removal
• Padlockable for security
• All switch ratings at AC-21
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 40A isolator with a 6-pole configuration. The isolator has a rotary switch and insulated enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 280 x 190 x 130mm
• 25mm Knock-outs
• Easy access and switch removal
• Padlockable for security
• Flame retardant material
• All switch ratings at AC-22
• Room in enclosure to add 1x extra auxiliary block either side of the switch
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 40A isolator with an 8-pole configuration. The isolator has a rotary switch and insulated enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 280 x 190 x 130mm
• 25mm Knock-outs
• Easy access and switch removal
• Padlockable for security
• Flame retardant material
• All switch ratings at AC-22
• Room in enclosure to add 1x extra auxiliary block either side of the switch
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 63A rated 3-pole isolator with a rotary switch in an IP65 rated ABS enclosure. This isolator is ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 175 x 125 x 90mm
• Easy access and switch removal
• Flame retardant material
• 25mm knock-outs
• Padlockable for security
• All switch rating at AC-21
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 63A rated isolator with a 3-pole + switched neutral configuration. The isolator has a rotary switch and an IP65 rated die cast enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 152 x 140 x 100mm
• Die Cast aluminium enclosure
• Lid RAL 7032, back box RAL 7043
• Early make/late break neutral contact
• Switched neutral contacts in blue for identification
• Easy access and switch removal
• Padlockable for security
• All switch ratings at AC-21
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 32A isolator with a 4-pole configuration. The isolator has a rotary switchand stainless steel enclosure. Particularly suitable for pharmaceutical and food preparation areas.

• Dimensions (H x W x D) 173 x 100 x 120mm
• Grade 304 brushed stainless steel
• Fully earth bonded
• Easy access and switch removal
• Padlockable for security
• All switch ratings at AC-22
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 63A isolator with a 4-pole configuration. The isolator has a rotary switchand stainless steel enclosure. Particularly suitable for pharmaceutical and food preparation areas.

• Dimensions (H x W x D) 178 x 178 x 135mm
• Grade 304 brushed stainless steel
• Fully earth bonded
• Easy access and switch removal
• Padlockable for security
• All switch ratings at AC-22
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 32A isolator with a 4-pole configuration. The isolator has a rotary switch and metal enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 173 x 100 x 120mm
• Epoxy coated steel enclosure
• Lid RAL 7032, back box RAL 7043
• Easy access and switch removal
• Padlockable for security
• All switch ratings at AC-22
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 63A isolator with a 4-pole configuration. The isolator has a rotary switch and metal enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 178 x 178 x 135mm
• Epoxy coated steel enclosure
• Lid RAL 7032, back box RAL 7043
• Easy access and switch removal
• Padlockable for security
• All switch ratings at AC-22
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 63A isolator with an 8-pole configuration. The isolator has a rotary switch and steel enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 400 x 300 x 200mm
• Epoxy coated strong steel
• Bottom gland plate
• Colour RAL 7035
• Easy access and switch removal
• Padlockable for security
• All switch ratings at AC-22
• Room in enclosure to add 1x extra auxiliary block either side of the switch
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

An 80A rated isolator with a 3-pole + switched neutral configuration. The isolator has a rotary switch and an IP65 rated ABS enclosure. This isolator is ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 175 x 125 x 90mm
• Early make/late break neutral contact
• Switched neutral contacts in blue for identification
• Insulated enclosure
• Easy access and switch removal
• Flame retardant material
• 20 or 25mm knock-outs (depending on rating)
• Padlockable for security
• All switch ratings at AC-21
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

An 80A isolator with a 4-pole configuration. The isolator has a rotary switch and metal clad enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 220 x 145 x 90mm
• Epoxy coated steel enclosure
• Lid RAL 7032, back box RAL 7043
• Easy access and switch removal
• Padlockable for security
• IP54 Rated
• All switch ratings at AC-21
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

An 80A isolator with a 6-pole configuration. The isolator has a rotary switch and steel enclosure. Ideal for the AC side of the inverter in photovoltaic installations.

• Dimensions (H x W x D) 400 x 300 x 200mm
• Epoxy coated strong steel
• Bottom gland plate
• Colour RAL 7035
• Easy access and switch removal
• Padlockable for security
• All switch ratings at AC-22
• Room in enclosure to add 1x extra auxiliary block either side of the switch
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

This 80 to 125A 1NO + 1NC volt free contact is designed for use with door interlocked and boxed isolator switch units.

• Easily connected
• Rear mounting
• Maximum terminal capacity 1.5mm²
• CB, CE, SEMKO, UL508
• Rear mounting
• Maximum terminal capacity 1.5mm²
• CB, CE, SEMKO, UL508