This 80 to 125A 2NO volt free contact is designed for use with door interlocked and boxed isolator switch units.

• Easily connected
• Rear mounting
• Maximum terminal capacity 1.5mm²
• CB, CE, SEMKO, UL508
• Rear mounting
• Maximum terminal capacity 1.5mm²
• CB, CE, SEMKO, UL508

This 20 to 63A 1NO + 1NC volt free contact is designed for use with door interlocked and boxed isolator switch units.

• Easily connected
• Rear mounting
• Maximum terminal capacity 1.5mm²
• CB, CE, SEMKO, UL508
• Rear mounting
• Maximum terminal capacity 1.5mm²
• CB, CE, SEMKO, UL508

This 20 to 63A 2NO volt free contact is designed for use with door interlocked and boxed isolator switch units.

• Easily connected
• Rear mounting
• Maximum terminal capacity 1.5mm²
• CB, CE, SEMKO, UL508
• Rear mounting
• Maximum terminal capacity 1.5mm²
• CB, CE, SEMKO, UL508

A 100A changeover switch with a 2-pole configuration in an ABS enclosure. The unit has a lockable rotary switch, padlockable in the Off position (up to 3x padlocks) for security, and is Bureau Veritas and Lloyds registered.

• Dimensions 254 x 180 x 137mm
• Under load operation
• Earth terminals included
• Captive +/- terminal screws
• Lid interlocked with switch in position 1 and 2
• IP65 Rating
• All switch ratings at AC-21
• Bureau Veritas and Lloyds registered
• cUL listed, IEC 60947-3

This 125A changeover switch has a 4-pole configuration and is fitted with an early make/late break neutral contact. The enclosure is of epoxy coated steel construction and the unit has a lockable rotary switch, padlockable in the Off position for security.

• Dimensions (H x W x D) 400 x 300 x 200mm
• Easy access and switch removal
• Padlockable for security
• Colour RAL 7035
• Bottom gland plate
• IP65 Rating
• All switch ratings at AC-22
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 25A changeover switch with a 2-pole configuration in an ABS enclosure. The unit has a lockable rotary switch, padlockable in the Off position (up to 3x padlocks) for security, and is Bureau Veritas and Lloyds registered.

• Dimensions 175 x 151 x 95mm
• Under load operation
• Earth terminals included
• Captive +/- terminal screws
• Lid interlocked with switch in position 1 and 2
• IP65 Rating
• All switch ratings at AC-21
• Bureau Veritas and Lloyds registered
• cUL listed, IEC 60947-3

This 25A changeover switch has a 4-pole configuration and is fitted with 2x early make/late break neutral contacts. The unit has a metal clad enclosure and sldo has a lockable rotary switch, padlockable in the Off position for security.

• Dimensions (H x W x D) 270 x 215 x 125mm
• Easy access and switch removal
• Padlockable for security
• Colours - lid RAL 7032, back box RAL 7043
• All switch ratings at AC-22
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 32A changeover switch with a 2-pole configuration in an ABS enclosure. The unit has a lockable rotary switch, padlockable in the Off position (up to 3x padlocks) for security, and is Bureau Veritas and Lloyds registered.

• Dimensions 175 x 151 x 95mm
• Under load operation
• Earth terminals included
• Captive +/- terminal screws
• Lid interlocked with switch in position 1 and 2
• IP65 Rating
• All switch ratings at AC-21
• Bureau Veritas and Lloyds registered
• cUL listed, IEC 60947-3

This 32A changeover switch has a 4-pole configuration and is fitted with 2x early make/late break neutral contacts. The unit has a metal clad enclosure and sldo has a lockable rotary switch, padlockable in the Off position for security.

• Dimensions (H x W x D) 270 x 215 x 125mm
• Easy access and switch removal
• Padlockable for security
• Colours - lid RAL 7032, back box RAL 7043
• All switch ratings at AC-22
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 40A changeover switch with a 2-pole configuration in an ABS enclosure. The unit has a lockable rotary switch, padlockable in the Off position (up to 3x padlocks) for security, and is Bureau Veritas and Lloyds registered.

• Dimensions 175 x 151 x 95mm
• Under load operation
• Earth terminals included
• Captive +/- terminal screws
• Lid interlocked with switch in position 1 and 2
• IP65 Rating
• All switch ratings at AC-21
• Bureau Veritas and Lloyds registered
• cUL listed, IEC 60947-3

This 40A changeover switch has a 4-pole configuration and is fitted with 2x early make/late break neutral contacts. The unit is of insulated ABS construction and has lockable rotary switches, padlockable in the Off position for security.

• Dimensions (H x W x D) 280 x 190 x 130mm
• 25mm Knock-outs
• Easy access and switch removal
• Padlockable for security
• IP65 Rating
• All switch ratings at AC-22
• Flame retardant material
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

This 40A changeover switch has a 4-pole configuration and is fitted with 2x early make/late break neutral contacts. The unit has a metal clad enclosure and sldo has a lockable rotary switch, padlockable in the Off position for security.

• Dimensions (H x W x D) 270 x 215 x 125mm
• Easy access and switch removal
• Padlockable for security
• Colours - lid RAL 7032, back box RAL 7043
• All switch ratings at AC-22
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

A 63A changeover switch with a 2-pole configuration in an ABS enclosure. The unit has a lockable rotary switch, padlockable in the Off position (up to 3x padlocks) for security, and is Bureau Veritas and Lloyds registered.

• Dimensions 180 x 182 x 137mm
• Under load operation
• Earth terminals included
• Captive +/- terminal screws
• Lid interlocked with switch in position 1 and 2
• IP65 Rating
• All switch ratings at AC-21
• Bureau Veritas and Lloyds registered
• cUL listed, IEC 60947-3

This 63A changeover switch has a 4-pole configuration and is fitted with 2x early make/late break neutral contacts. The unit has a metal clad enclosure and sldo has a lockable rotary switch, padlockable in the Off position for security.

• Dimensions (H x W x D) 270 x 215 x 125mm
• Easy access and switch removal
• Padlockable for security
• Colours - lid RAL 7032, back box RAL 7043
• All switch ratings at AC-22
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

This 63A changeover switch has a 4-pole configuration and is fitted with an early make/late break neutral contact. The enclosure is of epoxy coated steel construction and the unit has a lockable rotary switch, padlockable in the Off position for security.

• Dimensions (H x W x D) 400 x 300 x 200mm
• Easy access and switch removal
• Padlockable for security
• Colour RAL 7035
• Bottom gland plate
• IP65 Rating
• All switch ratings at AC-22
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

This 80A changeover switch has a 4-pole configuration and is fitted with an early make/late break neutral contact. The enclosure is of epoxy coated steel construction and the unit has a lockable rotary switch, padlockable in the Off position for security.

• Dimensions (H x W x D) 400 x 300 x 200mm
• Easy access and switch removal
• Padlockable for security
• Colour RAL 7035
• Bottom gland plate
• IP65 Rating
• All switch ratings at AC-22
• CB, CE, SEMKO, UL508, IEC, EN 60947-3

Black flush pushbutton switch from Europa Components, designed for 22.5mm diameter panel cut outs.

• Fully sealed to IP65
• Fully interchangeable with other popular series
• Supplied complete with mounting block
• Flush push-button with metal bezel
• Range of accessories also available

Green flush pushbutton switch from Europa Components, designed for 22.5mm diameter panel cut outs.

• Fully sealed to IP65
• Fully interchangeable with other popular series
• Supplied complete with mounting block
• Flush push-button with metal bezel
• Range of accessories also available

Blue flush pushbutton switch from Europa Components, designed for 22.5mm diameter panel cut outs.

• Fully sealed to IP65
• Fully interchangeable with other popular series
• Supplied complete with mounting block
• Flush push-button with metal bezel
• Range of accessories also available

A non-illuminated twist to release emergency stop button from Hylec with reset red mushroom head. This robust, sealed control station has been specially designed and manufactured for use in the electrical and electronic engineering markets.

This 22mm push button control station is aesthetically appealing and modularly designed to make assembly and interchangeability easy.

• Sealed up to IP66
• Insulation resistance >100MΩ @ 500V DC
• Unique snap on DIN rail and flange brackets
• Dust and waterproof for short-term submersion
• 2 contact blocks fitted as standard - 1x NO & 1x NC
• Contacts - silver bifurcated and serrated
• Operating temperature -10 to +65°C
• Manufacturer's part 1DE.01.01AG

Non-illuminated push button control station with a green flush head, contact blocks 1x N.O. and 1x N.C. This unique robust, sealed control station has been specially designed and manufactured for use in the electrical and electronic engineering markets.

A non-illuminated standard 2-position key control selector switch station from Hylec.

• Standard base
• Size 80 x 73 x 53mm
• Enclosure material: flame retardant ABS UL94-HB
• Colour: grey
• Sealed up to IP56
• Maximum temperature rating 65°C
• Manufacturer's part 1DE.01.09AG

A non-illuminated twist to release emergency stop station from Hylec with a red stop, green flush head start, yellow cover and grey base. This sealed control station has been specially designed and manufactured for use in the electrical and electronic engineering markets.

• Standard base
• Size 80 x 106 x 53mm
• Material: Flame retardant ABS UL94-HB
• Sealed up to IP56
• Manufacturer's part 1DE.02.01AG

A non-illuminated foot/palm switch control station from Hylec with a large black domed head.

• Standard base
• Size 85 x 69 x 102.5mm
• Enclosure made from flame retardant ABS UL94-HB
• Black base
• Grey lid
• Sealed up to IP66
• Maximum temperature 65°C
• Manufacturer's part 1DE.SP.21NB

A non-illuminated foot/palm switch control station from Hylec with a large green domed head.

• Standard base
• Size 85 x 69 x 102.5mm
• Enclosure made from flame retardant ABS UL94-HB
• Black base
• Grey lid
• Sealed up to IP66
• Maximum temperature 65°C
• Manufacturer's part 1DE.SP.21NG

A non-illuminated foot/palm switch control station from Hylec with a large red domed head. This is a spring-loaded momentary push button switch with 1 NO and 1 NC contact.

• Standard base
• Size 85 x 69 x 102.5mm
• Enclosure made from flame retardant ABS UL94-HB
• Black base
• Grey lid
• Sealed up to IP66
• Maximum temperature 65°C
• Manufacturer's part 1DE.SP.21NR

A Hylec Emergency stop shroud in yellow, 22mm bezel for use with 40mm operating head.

• Dimensions 80 x 35 x 67mm

A 10A, 240V, 1-way rotary switch complete with a grey enclosure.

• 10A, 240/250V
• 1-way
• Complete with grey enclosure
• IP66 ingress rating
• Compliant with IEC 60669-1 and IEC 60529
• Schneider Electric type 56SW110GY

A complete start/stop control station with two 22mm diameter flush push-buttons.

• Product or component type: complete control station
• Operator profile: 2 flush push-buttons
• 1 button red 1 NC '0' marking
• 1 button green 1 NO 'I' marking
• Contacts operation: slow-break
• Colour of base of enclosure: light grey RAL 7035
• Colour of cover: dark grey RAL 7016
• Material: polycarbonate
• Product range: Harmony XALD
• Schneider Electric type XALD213

A complete emergency stop station with a red 40mm button.

• Control station application: emergency stop button
• 1 Ø 40mm mushroom head push-button
• Reset: turn to release
• Operator description: red unmarked 1 NC
• Contacts operation: Slow-break
• Colour of base of enclosure: light grey RAL 7035
• Colour of cover: yellow RAL 1021
• Material: polycarbonate
• Product range: Harmony XALK
• Schneider Electric type XALK178

An emergency stop switch disconnector from Schneider Electric's VCCF series.

The switch is designed to mount at the back of an enclosure and is supplied with an extension shaft, allowing the switch actuator to be mounted on the front panel of the enclosure.

• Current rating: 63A
• 3 NO contacts
• Schneider Electric type VCCF3

An emergency stop switch disconnector from Schneider Electric's VCCF series.

The switch is designed to mount at the back of an enclosure and is supplied with an extension shaft, allowing the switch actuator to be mounted on the front panel of the enclosure.

• Current rating: 125A
• 3 NO contacts
• Schneider Electric type VCCF5

A pendant control station from Schneider Electric's XACA series.

• 2 button model plus emergency stop
• First push-button 1 NO raise, slow
• Second push-button 1 NO lower, slow
• Stop push-button Ø 30 mm 1 NC latching
• Mechanical interlock
• Pistol grip
• Complete, ready for use
• IP65 rated
• Schneider Electric type XACA2013

A dark grey control station from Schneider Electric's XALD series.

• 2 button model
• Button colours: green and red
• Labels: Start & Stop
• Cover colour: dark grey RAL 7016
• Base colour: light grey RAL 7035
• Schneider Electric type XALD211H29

High quality enclosure from Spelsberg with cut-out for mounting industry standard 22.5mm diameter controls.

• Ideal for emergency stop buttons, key switches and indicators
• High visibility yellow lid
• Rugged enclosure suitable for harsh environments
• Offers high weather, UV and impact resistance
• Lid secured by four captive black plastic bolts
• Box base has two PG11/16 cable entries
• Dimensions 65 x 65 x 57mm
• Ingress protection to IP65
• Spelsberg BM series

This black 2-position key switch from Techna is a high quality key selector switch with keys removable in both positions.

• Fully sealed to IP65
• Supplied complete with mounting block
• 2 position stay put actuator
• All metal construction

This black 3-position key switch from Techna is a high quality key selector switch with keys removable in each position.

• Fully sealed to IP65
• Supplied complete with mounting block
• 3 position stay put actuator
• All metal construction

High quality emergency stop mushroom head push button from Techna with key to release actuation.

• Red colour
• Metal bezel
• Non-illuminated
• Knob size 40mm
• Fully sealed to IP65

Note: These stop buttons require a control block.

Mushroom head stop push button from RAAS with push to stay, pull to release actuation.

• Red colour
• Metal bezel
• Non-illuminated
• Knob size 40mm
• Fully sealed to IP65

Note: These stop buttons require a control block

Short handle 2-position stay put selector from Techna.

• Compatible with Telemecanique ZB2 series
• Non-illuminated
• Black actuator
• Fully sealed to IP65

Short handle 3-position stay put selector from Techna.

• Compatible with Telemecanique ZB2 series
• Non-illuminated
• Black actuator
• Fully sealed to IP65

Contact block from Techna suitable for use with RC*M enclosures.

• 1NO contact type
• IP65 rated enclosure
• Base mount

Contact block from Techna suitable for use with RC*M enclosures.

• 1NC contact type
• IP65 rated enclosure
• Base mount

High quality stop button from Techna with a 'Turn to Release' actuation.

• Red colour
• Metal bezel
• Non-illuminated
• Knob size 40mm
• Fully sealed to IP65

Please note: these stop buttons require a control block (see order codes 78-3730 and 78 ‑3732).