The Bastech BT-300 WT is a Wire Tracker Cable and Lead Finder that is used for the fast detection of pairs of wires, cables and lines using the continuity check, line and polarity test.

The BT -300 WT consists of a transmitter and receiver. The transmitter sends a reference signal on the line to be followed, and this signal can be detected with the receiver and so the cable can be identified.

The power to the BT-300 WT is supplied by a 9V battery in the receiver and 3x AAA batteries in the transmitter.

What's in the box?Cable detector transmitter and receiverBattery (9V block)Battery 3x AA MignonHeadsetLAN cable RJ45Telephone cable with modular connector RJ11Test cable for battery with alligator clipsOperating instructions

• Volume control
• Adjustable test speed
• Continuity test
• Flashlight function
• Manufacturer's part: Basetech BT-300 WT

Tracing cables in walls, identifying which safety devices are connected to certain circuits, or locating an interrupted wire in a cable or pipe. These can often be tiresome and time-consuming practices, but not so if you have the Fluke 2042 in your tool kit.This is a professional general purpose cable locator. It is ideal for tracing cables in walls and underground. It can be used for locating fuses and breakers on final circuits and locating interruptions and short-circuits in cables and electrical floor heating systems. It can also be used for tracing metallic water and heating pipes. The Fluke 2042 comprises a transmitter that supplies a modulated alternating voltage to the cable to generate an electrical field around it, and a receiver with a coil that is placed close to cable. A voltage is induced in the coil, which is shown on the display. To prevent incorrect readings caused by interfering fields from things like electronic fluorescent lamp ballasts or frequency converters, and uses a digitally coded transmitter signal. The unit is supplied as a complete kit comprising of a transmitter and receiver in a purpose-made carry case.

• For all applications (live or dead cables)
• Ideal for tracing cables in walls and underground
• Includes a transmitter and a receiver
• Proven digitally coded sender signal
• Torch function for dark areas
• Locates fuses/breakers on final circuits and locating interruptions
• Can also be used for tracing metallic water and heating pipes
• Automatic or manual adjustment of receiving signal sensitivity
• Acoustical receiving signal switchable
• Auto-power - Off
• Additional transmitters are available for extension of to distinguish between several signals
• Supplied with transmitter, receiver, test lead, soft carrying case, hard case, batteries and user manual

The Fluke 2042T is a Professional General Purpose Cable and Lead Finder (Locator, (Transmitter Only)). It is ideal for tracing cables in walls and underground, locating fuses/breakers on circuits and locating interruptions and short-circuits in cables and electrical floor heating systems. The 2042T can also be used for tracing metallic water and heating pipes.

The 2042T can be used as an additional transmitter for the Fluke 2042 cable locator. One additional transmitter can be used per cable locator set.

What's in the Box?Fluke 2042T 6x AA batteriesUser manual

• For all applications (live or dead cables) without additional instruments
• Proven digitally coded sender signal guarantees clear signal identification
• Transmitter with LC-display for transmitting level, transmitting code and external voltage
• Automatic or manual adjustment of receiving signal sensitivity
• Auto-Power-Off
• Additional torch lamp function for working in dark environments
• Supplied as a transmitter only
• Manufacturer's part: Fluke 2042T

The Fluke Networks Pro3000 Analogue Tone Generator and Probe is your best choice for toning and tracing wire on non-active networks, and specifically for identifying individual pairs with SmartTone® technology. The angled bed-of-nails clips allow easy access to individual wires, and the RJ-11 connector is ideal for use on telephone jacks.

The Pro3000 Analogue Probe has an ergonomic sleek design making it easy to handle and use. The large speaker on the probe makes the tone easier to hear through walls, enclosures, wood or plaster. A recessed On/Off button helps prevent the probe from accidentally being turned on in the pouch.

What's in the Box?Fluke Networks Pro3000 Analogue Tone GeneratorFluke Networks Pro3000 Analogue Probe2x Angled Bed-of-Nails Clips1x RJ11 PlugNylon carrying pouchInstructions

Tone Generator features:

• SmartTone technology provides five distinct tones for exact pair identification
• Sends loud tone up to 10 miles (16km) on most cables
• Loud speaker on Probe makes the tone easier to hear through drywall, wood, and other enclosures
• Angled bed-of-nails clips allow easy access to individual pairs
• RJ-11 connector is ideal for use on telephone jacks
• Attach nylon pouch (included in kit) to your belt for easy transport

Probe features:

• Loud large speaker amplifies tone through walls, enclosure, wood or plaster
• Easy-to-use adjustable volume control dial
• Quick-twist tip for easy replacement
• Free spare tip inside Pro3000 Tone and Probe Kit
• Manufacturer's part: Fluke Networks 26000900 PRO3000 Sounder and Probe Kit

The Fluke Networks 26200900 Pro3000 Analogue Tone Generator/ Sounder is your best choice for toning and tracing wire on non-active networks, and specifically for identifying individual pairs with SmartTone® technology.

The angled bed-of-nails clips allow easy access to individual wires, and the RJ-11 connector is ideal for use on telephone jacks. When touching the wires together and momentarily shorting the far end of a cable pair, the SmartTone technology will change the cadence of the tone generated. This tone change you hear through the probe positively verifies the correct wire pair. SmartTone provides five distinct tones for exact pair identification. You can send this loud tone up to 10 miles (16 kilometres) on most cables.

What's in the Box?Pro3000 Analogue Tone Generator9V BatteryUser manual

• SmartTone technology
• Send tone signal up to 10 miles on most cables
• Line cord features angled bed-of-nails clips
• Ruggedised RJ-11 plug for direct access to phone and data jacks without adapters
• External switch allows selection of solid or alternating tone options
• Continuity testing
• Line polarity confirmation
• Manufacturer's part: Fluke Networks 26200900 PRO3000 Sounder

The Fluke Networks CIQ-IDK57 is a CableIQ Remote Identifier Set 5-7. The CableIQ Remote Identifiers are for use with the CableIQ Qualification Tester. They are part of a series designed for residential installers who need to document that cabling systems are installed properly and will perform reliably. They quickly qualify residential cabling systems to support voice, VoIP, 10/100/1000 Ethernet and CATV and presents results in the form of professional test reports.

CableIQ is versatile and intuitive enough to replace multiple tools for testing, ID-tagging and troubleshooting all voice, data, video, audio and security cabling.

• Supplied: Remote Identifier Set 5-7
• Manufacturer's part: Fluke Networks CIQ-IDK57

The Voltcraft LSG-10B is a Transmitter for use with the Voltcraft LSG-10. In extensive installations, this additional transmitter provides for a more reliable cable localisation with broader search signals, allowing for convenient and time-efficient scanning without the need of repositioning the transmitter all the time. The search signals can be coded (1 to 7) and be identified with the receiver of the cable-searching device LSG-10.

What's in the Box?Transmitter LSG-10B1x 9V block battery2 safety test leads2 pluggable measuring tips2 safety alligator clipsOperating instructions

• Suitable for LSG-10
• Adjustable transmitter codes
• Supports simultaneous use of up to 7 transmitters
• Suitable for LSG-10
• Adjustable transmitter codes
• Supports simultaneous use of up to 7 transmitters
• Manufacturer's part: Voltcraft LSG-10B

The Voltcraft Cable ID adaptors Remote ID2-ID8 allow remote ID, in association with the LAN cable tester CT-20TDR, and can identify up to 8 cables. The reporting (ID) of the adaptor is displayed directly on the main unit.

What's in the Box?7 remote IDs Pannier Manual

• Suitable for: LAN cable tester CT-20TDR
• Calibrated to: Factory setting
• Manufacturer's part: Voltcraft Remote ID2-ID8