The Basetech BT-100 is a Cable Tester for unshielded (UTP) or shielded (STP/FTP) RJ-45 modular plug systems up to CAT7 or RJ-11 (RJ-12) modular plugs with 2 to 6 wires.

Each wire of the connected cable is individually tested and the classification is shown on a clear luminous bar display. The testing process runs automatically. The classification of the wires or possible errors such as open circuit or short circuit can be read directly.

What's in the Box?TransmitterReceiver1x 9V batteryBagInstruction manual

• Two test speeds (Normal/ Slow)
• Test of installed cables by external receiver possible
• Screening test
• For RJ11 and RJ45
• Single core test
• Easy to read display
• Manufacturer's part: Basetech BT-100

The Basetech BT-200 is a Cable Tester for unshielded (UTP) or shielded (STP/FTP) RJ-45 modular plug systems up to CAT7, respectively RJ-11 (RJ-12) modular plug with 2 to 6 cores. Each core of the connected cable is individually tested and the allocation is shown on a clearly arranged bar graph display.

The test sequence is automatic. The allocation of the cores, respectively potential errors such as interruption and short circuit can be read directly.

In addition, the BNC coaxial cable can be tested for continuity, interruption and short circuit.

What's in the Box?Transmitter unitReceiver unitBNC Remote unit9V BatteryCarrying bagOperating instructions

• Two test speeds (Normal/ Slow)
• Test of installed cables by external receiver possible
• Screening test
• Manufacturer's part: Basetech BT-200

The CT20 allows a single user to quickly identify and label two wires even when the wire ends are located in different rooms. The CT-20 can also be used as a standard continuity tester. This tester is shipped fully tested and with proper use will provide years of reliable service.

• Routing can be easily tested
• Lines assigned with only one person
• Dimensions: (L x W x H) 90 x 57 x 27mm
• Max. cable length: 3000m
• Measurements: Identification, passage, interruption
• Power supply: 9V battery pack
• Suitable for: Identification, continuity, interruption measurement
• Weight: 260g
• Supplied remote unit, battery (9V PP3), belt holster and user manual

The Fluke Networks FTK1000 is a SimpliFiber Pro Basic Fibre Verification Kit which combines all vital tools required to verify and troubleshoot optical fibre cabling systems, measure loss and power levels, and inspect and clean connector end-faces.

The FTK1000 meter is supplied with a visual fault locator which can verify continuity and polarity, and provide assistance to find breaks and bends in cables, and locate problems in connectors and splices.

The Fluke SimpliFiber Verification Kit is the right equipment for contractors and network technicians to perform preventive inspections, install and maintain premises networks with both multimode and single mode optical fibre. This Basic Verification Kit is a great starter kit for network technicians and contractors who install and maintain fibre links.

Applications: Sensing and Instrumentation; Signal Processing; Test and Measurement; Communications and Networking.

What's in the Box?SimpliFiber Pro optical power meter850/1300 multimode sourceUSB cable for PC communicationsGetting Started GuideSimpliFiber Pro Product Manuals CDLinkWare Software CDCarrying case

• Simple-to-use fibre-loss tester with advanced time-saving features
• Single-port, simultaneous dual-wavelength feature completes testing in half the time
• Saves measurements from both wavelengths into one record
• Additional 1490 and 1625nm wavelengths extends product use to broader applications
• CheckActive feature emits an audible tone and displays an icon when a live fibre is detected
• FindFiber Remote ID enables one individual to quickly identify cable connections or routings
• Min/Max capability automates precision tracking of intermittent power fluctuations
• Large internal memory save 1000 results which enables continuous testing and recording
• LinkWare Cable Test Management software helps analyze test results and create test reports
• Manufacturer's part: Fluke Networks FTK1000

The Megger TDR500/3 cable tester uses time domain reflectometry to locate faults on metallic cables. It has a minimum resolution of 0.1 m and a 5 km maximum range depending on velocity factor selected and cable type. With four output impedances (25, 50, 75, and 100Ω) and a velocity factor from 0.2 to 0.99 it meets any cable test requirement. The TDR500/3 is a hand held, compact instrument which is simple and intuitive to use.

The AUTO option sets the gain and pulse width based on the range required and the cable type, aiding rapid diagnosis of the TDR trace. A clear operator controlled cursor allows easy measurement of the distance to the fault. A trace HOLD feature also allows the operator to hold a trace on the screen, something not seen on most other handheld TDRs. Its clear, high contrast screen helps the user in identify key events on the trace.

• Backlit monochrome graphics LCD (256 x 128)
• Resolution to 0.1m
• For use on Telecom TNV-3 circuit, or 150V CAT IV power circuits
• Power blocking filter not required
• 2ns pulse for near end fault location
• AUTO selects gain and pulse for each range
• Display distance in metres or feet
• Uses five AA (LR6) batteries
• Environmental protection to IP54
• Dimensions 48 x 230 x 115mm
• Weighs 600g

A multifunctional remote network cable tester that is small and easy to use and features a removable remote unit for the testing of cables in situ. This versatile unit can test RJ45 (shielded and unshielded twisted pairs).

• Small size and easy to carry
• Simple to operate
• Open circuit, short circuit, straight and crossover test functions
• LED and sound indication
• Auto/manual select switch
• Sound On/Off switch
• Power saving mode
• Battery power status indication
• Powered by 12V GP23AE type (supplied - for suitable replacement see Batteries section)
• Dimensions 90 x 50 x 24mm
• Weight 68g

The Voltcraft CT-20TDR is a Multifunction LAN Cable Tester that enables the checking of 2 to 8-pin cables and their shielding. There are 5 test modes to choose from: LAN mode, the phone mode, Coax mode, tracking mode and linear mode. In each mode, specific cable and number of cores can be chosen. The test procedure is automatic and the results are displayed graphically and in plain easy to understand text.

What's in the Box?Remote connection measurements (ID1) 2 adaptors F/ BNC 2 reduction western RJ45/ RJ11 Belt Clip Soft Case Batteries

• Cable Testing
• Length Measurement
• Tone generator for cable location
• Backlit dot matrix display
• Option measurements have attached cables to connect remote measurements
• Localization distance and fault in cable length from 1 to 350m
• For CAT3, CAT4, CAT5, CAT5E, CAT6 and coax shielded / unshielded
• Input is protected against overvoltage transient and a ringing signal
• Manufacturer's part: Voltcraft CT-20TDR

The Voltcraft CT-7 cable tester quickly and easily tests all common computer cables for continuity, short circuit, open ends, crossover, incorrect wiring, etc.. An easy-to-read LED display allows you to test each conductor in turn, manually or automatically, so that you can check for multiple ground connections, incorrect crossed connections, or detect breaks in the wire.

• For all common computer and network cables
• Clear illuminated bar display
• Adjustable for 2, 4, 6, 9, 15, 25 or 36 cables
• Channel, connection, allocation and shield tests
• Display of allocation via LEDs
• Automatic and manual test cycle (easily adjustable)
• Suitable for 9-pin, 15-pin, 25-pin SUB-D, 15-pin SUB-HD and Centronics
• Plus: USB A + B, IEEE 1394, BNC, RJ-45, PS/2, 5-pin DIN and SATA