This is the Analog Devices OP400GPZ quad, low-power op amp. Ideal choice for applications requiring multiple precision operational amplifiers and where low power consumption is critical.

• Operational amplifier
• Low offset
• Low power type
• Quad amplifiers
• 500kHz bandwidth
• 0.15V/us slew rate
• 80uVDC input offset voltage
• 7000V/mV gain
• 135dB CMRR
• 3 to 18VDC supply voltage
• 0°C to +70°C
• DIL-14 case
• Low input offset voltage
• Low offset voltage drift
• Low supply current
• High open-loop gain
• Input bias current
• Low noise voltage density
• Stable with large capacitive loads

Due to Global supply chain disruptions, we are unable to supply lead times for quantities above our current stock holding. For further delivery information please contact our sales team: sales.support@rapidonline.com

A BiMOS operational amplifier suitable for single supply amplifiers, sample and hold amplifiers, timers/multivibrators, photocurrent instrumentation, peak detectors, active filters, comparators, function generators, tone controls, power supplies, portable instruments, intrusion alarm systems.

• Dual amplifiers
• 4.5MHz Bandwidth
• 9V/us Slew rate
• MOSFET Input / bipolar output
• 5mV Input offset voltage
• 100kV/V Gain
• 90dB CMRR
• 4 to 36V Supply voltage
• -40°C to +85°C
• DIL-8 Case

The Linear Technology LT1112 dual operational amplifiers achieve a new standard in combining low cost and outstanding precision specifications. The performance of the selected prime grades matches or exceeds competitive devices. In the design of the LT1112 however, particular emphasis has been placed on optimising performance in the low cost plastic and SO packages. For example, the 75µV maximum offset voltage in these low cost packages is the lowest on any dual or quad non-chopper operational amplifier.

The LT1112 also provides a full set of matching specifications, facilitating their use in such matching dependent applications as two and three operational amplifier instrumentation amplifiers. Another set of specifications is furnished at ±1V supplies. This, combined with the low 320µA supply current per amplifier, allows the LT1112 to be powered by two nearly discharged AA cells.

• Offset voltage 75µV max
• Offset voltage drift: 0.5µV/°C max
• Input bias current: 250pA max
• 0.1Hz to 10Hz noise: 0.3µV P-P, 2.2pA P-P
• Supply current per amplifier: 400µA max
• CMRR: 120dB min
• Voltage gain: 1 million min
• Specs with ±1.0V supplies
• Operating temp.: -40 to +85°C

A BiMOS operational amplifier suitable for single supply amplifiers, sample and hold amplifiers, timers/multivibrators, photocurrent instrumentation, peak detectors, active filters, comparators, function generators, tone controls, power supplies, portable instruments, intrusion alarm systems.

• Single amplifier
• 4.5MHz Bandwidth
• 9V/us Slew rate
• MOSFET Input / bipolar output
• 5mV Input offset voltage
• 100kV/mV Gain
• 90dB CMRR
• 4 to 36V Supply voltage
• -55°C to +125°C
• DIL-8 Case

This is the ST LM324DT quad low power drain op amp. Application areas include transducer amplifiers, DC gain blocks and all the conventional op amp circuits. Features include single or dual voltage supplies, this device is particularly suited to battery operation.

• Operational amplifier
• Low power type
• Quad amplifiers
• 1.3MHz Bandwidth
• Single 3 to 32VDC supply voltage
• Or dual ±1.5VDC to ±15VDC supply voltages
• 0°C to +70°C
• SO-8 case
• High gain
• Internally frequency compensated
• Internally frequency compensated for unity gain
• Large DC voltage gain
• Wide bandwidth
• Very low supply current drain

This is the ST LM358AD dual low power op amp.It is part of the LM158 series. Application areas include transducer amplifiers, DC gain blocks.

• Operational amplifier
• Low power type
• Dual amplifiers
• 1.1MHz bandwidth
• 0.6V/us slew rate
• 2mVDC input offset voltage
• 100V/mV gain
• 85dB CMRR
• Single 3 to 30VDC supply voltage
• Or dual ±16VDC supply voltage
• 0°C to +70°C
• 8-SOIC case
• Internally frequency-compensated
• Large DC voltage gain
• Wide bandwidth
• Very low supply current
• low input bias current
• low input offset voltage
• low input offset current

This is the ST LM358D dual low power op amp. It is part of the LM158 series. Application areas include transducer amplifiers, DC gain blocks.

• Operational amplifier
• Low power type
• Dual amplifiers
• 1.1MHz bandwidth
• 0.6V/us slew rate
• 2mVDC input offset voltage
• 100V/mV gain
• 85dB CMRR
• Single 3 to 30VDC supply voltage
• Or dual ±16VDC supply voltage
• 0°C to +70°C
• SO-8 case
• Internally frequency-compensated
• Large DC voltage gain
• Wide bandwidth
• Very low supply current
• Low input bias current
• Low input offset voltage
• Low input offset current

This is the ST LM358DT dual low power op amp. It is part of the LM158 series. Application areas include transducer amplifiers, DC gain blocks.

• 1.1MHz bandwidth
• 100V/mV gain
• Single 3 to 30VDC supply voltage
• Or dual ±16VDC supply voltage
• 0°C to +70°C
• SO-8 case
• Internally frequency-compensated
• Large DC voltage gain
• Wide bandwidth
• Very low supply current
• Low input bias current
• Low input offset voltage
• Low input offset current

A general purpose JFET-input operational amplifier incorporates well-matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit.

• Dual amplifiers
• 4MHz Bandwidth
• 16V/us Slew rate
• 3mV Input offset voltage
• 200V/mV Gain
• JFET Input
• 86dB CMRR
• 6 to 36V Supply voltage
• 0°C to +70°C
• SO-8 Case

This is the ST UA741CD single, general purpose op amp. Suitable for summing amplifiers, voltage followers, integrators, active filters and function generators.

• General purpose type
• Single amplifier
• 1MHz bandwidth
• 0.5V/us slew rate
• 1mV input offset voltage
• 200V/mV gain
• 90dB CMRR
• ±15VDC supply voltage
• 0°C to +70°C
• SO-8 case
• Large input voltage range
• No Latch-up
• High gain
• Short-circuit protection
• No frequency compensation required

The ISO122P is a precision isolation amplifier incorporating a novel duty-cycle modulation - demodulation technique. The signal is transmitted digitally across a 2pF differential capacitive barrier. With digital modulation the barrier characteristics do not affect signal integrity, thus resulting in excellent reliability and good high-frequency transient immunity across the barrier. Both barrier capacitors are imbedded in the plastic body of the package.

The ISO122P is easy to use. No external components are required for operation. The key specifications are 0.020% maximum nonlinearity, 50kHz signal bandwidth, and 200V/°C V_OS drift. A power supply range of 4.5 to 18V and quiescent currents of 5mA on V_S1 and ±5.5mA on V_S2 make the ISO122P ideal for a wide range of applications.

The ISO122P is contained in a 16-pin plastic DIP package.

• 100% tested for high-voltage breakdown
• Rated 1500Vrms
• High IMR: 140dB at 60Hz
• Bipolar operation: V_O = ±10V
• 16-pin plastic DIP package
• Fixed Unity Gain configuration
• 0.020% Maximum non-linearity
• ±4.5V to ±18V supply range
• Applications include: Transducer Isolator, Isolator for Thermocouples, RTDs, Pressure Bridges, and Flow Meters, 4mA to 20mA Loop Isolation, Ground Loop Elimination, Motor and SCR Control, Power Monitoring, PC-Based Data Acquisition, Test Equipment
• Texas Instruments type ISO122P

A wide-band JFET-input operational amplifier incorporates well-matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit.

• Dual amplifiers
• 4MHz Bandwidth
• 16V/us Slew rate
• 3mV Input offset voltage
• 200V/mV Gain
• JFET Input
• 86dB CMRR
• 6 to 36V Supply voltage
• 0°C to +70°C
• DIL-8 Case

A general purpose JFET-input operational amplifier incorporates well-matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit.

• Dual amplifiers
• 5MHz Bandwidth
• 12V/us Slew rate
• 3mV Input offset voltage
• 200V/mV Gain
• JFET Input
• 100dB CMRR
• 15 to 20V Supply voltage
• 0°C to +70°C
• DIL-8 Case

This is the Texas Instruments LM318P single high speed op amp. It is a precision, high speed, high slew rate op amp and features a factor of 10 speed increase over general purpose op amps without losing DC performance. Suitable for A/D converters, oscillators, active filters, sample and hold circuits, or general purpose amplifiers. Identical to the LM118 and LM218 op amps except for the operating temperature range (see below).

• General purpose amplifier
• High speed type
• Single amplifier
• 15MHz bandwidth
• 50V/us slew rate
• 200V/mV gain
• 100dB CMRR
• ±5 to ±20VDC supply voltage
• 0°C to +70°C
• DIL-8 case
• Internal frequency compensation
• Input and output overload protected

This is the Texas Instruments LM324N quad general purpose op amp.

• General purpose type
• Quad amplifier
• 1MHz bandwidth
• 2mVDC input offset voltage
• 100dB DC voltage gain
• 100dB CMRR
• Single 3 to 32VDC supply voltage
• Or dual ±1.5 to ±16VDC supply voltage
• 0°C to +70°C
• DIL-14 case

This is the Texas Instruments LM358AP dual low power op amp. It is part of the LM158 series. Application areas include transducer amplifiers, DC gain blocks.

• Operational amplifier
• Low power type
• Dual amplifiers
• 1.1MHz bandwidth
• 0.6V/us slew rate
• 2mVDC input offset voltage
• 100V/mV gain
• 85dB CMRR
• Single 3 to 30VDC supply voltage
• Or dual ±16VDC supply voltage
• 0°C to +70°C
• DIL-8 case
• Internally frequency-compensated
• Large DC voltage gain
• Wide bandwidth
• Very low supply current
• Low input bias current
• low input offset voltage
• low input offset current

For datasheet see here.

This is the Texas Instruments LM741 single general purpose op amp. Features short circuit protection. The high gain and wide range of operating voltage provide superior performance in integrator, summing amplifier and general feedback applications.

• General purpose type
• Single amplifier
• 0.5V/us slew rate
• 2mV DC input offset voltage
• 200V/mV gain
• 90dB CMRR
• ±13V DC supply voltage
• 0°C to +70°C
• DIL-8 case

This device is a monolithic, high performance audio operational amplifier that combines excellent DC and AC characteristics. Features very low noise, high output drive capability, high unity-gain and maximum-output-swing bandwidths, low distortion, high slew rate, input protection diodes and output short circuit protection.

• Internally compensated for unity-gain operation
• 100V/mV Gain
• Recommended operating voltage 5V to 15V
• Ambient temperature 0 to +70°C
• DIL-8 Case

Low noise operational amplifier from Texas Instruments.

• High output-drive capability
• High unity-gain and maximum-output-swing bandwidths
• Low distortion and high slew rate
• Bandwidth 10MHz
• 8-DIP case

This is the National Semiconductor RC4558 dual, general purpose op amp. Ideal for voltage-follower applications.

• General purpose type
• Dual amplifiers
• 3MHz bandwidth
• 1.7V/us slew rate
• 0.5mVDC input offset voltage
• 3MHz gain
• 90dB CMRR
• 5VDC to 15VDC supply voltage
• 0°C to +70°C
• 8-DIP case
• Continuous short-circuit protection
• Wide common-mode and differential voltage Ranges
• No frequency compensation required
• Low power consumption
• No latch-up
• Unity-gain bandwidth
• Low noise
• Gain and phase match between amplifiers

This JFET operational amplifier is a low noise amplifier that features high input impedance, wide bandwidth, high slew rate, and low input offset and input bias currents.

• Low noise
• Dual amplifiers
• Wide common-mode and differential voltage ranges
• Output short-circuit protection
• Internal frequency compensation
• 1MHz Bandwidth
• 6V/mV Gain
• JFET Input
• 76dB CMRR
• 6 to 36V Supply voltage
• 0°C to +70°C
• DIL-8 Case

This JFET operational amplifier is a low noise amplifier that features high input impedance, wide bandwidth, high slew rate, and low input offset and input bias currents.

• Low noise
• Dual amplifiers
• High input impedance JFET input stage
• Wide common-mode and differential voltage ranges
• Output short-circuit protection
• Internal frequency compensation
• 4MHz Bandwidth
• 200V/mV Gain
• JFET Input
• 86dB CMRR
• 6 to 36V Supply voltage
• 0°C to +70°C
• DIL-8 Case

A general purpose JFET operational amplifier that is a well-matched, high-voltage JFET and incorporates bipolar transistor in a monolithic integrated circuit.

• 4MHz Bandwidth
• 13V/us Slew rate
• 3mV Input offset voltage
• 200V/mV Gain
• JFET Input
• 86dB CMRR
• 6 to 36V Supply voltage
• 0°C to +70°C
• DIL-8 Case

A general purpose JFET-input operational amplifier incorporates well-matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit.

• Dual amplifiers
• 4MHz Bandwidth
• 16V/us Slew rate
• 3mV Input offset voltage
• 200V/mV Gain
• JFET Input
• 86dB CMRR
• 6 to 36V Supply voltage
• 0°C to +70°C
• DIL-8 Case

A general purpose JFET-input operational amplifier incorporates well-matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit.

• Quad amplifiers
• 4MHz Bandwidth
• 16V/us Slew rate
• 3mV Input offset voltage
• 200V/mV Gain
• JFET Input
• 86dB CMRR
• 6 to 36V Supply voltage
• 0°C to +70°C
• DIL-14 Case

LinCMOS programmable operational amplifier suitable for transducer interfacing, analogue calculations, amplifier blocks, active filters and signal buffering.

• Low power type
• Single amplifier
• 1.7MHz Bandwidth
• 3.6V/us Slew rate
• 1.1mV Input offset voltage
• 85dB CMRR
• 3 to 16V Supply voltage
• 0°C to +70°C
• DIL-8 Case
• Input offset voltage drift
• Single-supply operation
• Low noise
• High input impedance
• End-protection circuitry

This is the ST UA741CP single, general purpose op amp. Suitable for summing amplifiers, voltage followers, integrators, active filters, and function generators.

• General purpose type
• Single amplifier
• 1MHz bandwidth
• 0.5V/us slew rate
• 1mV input offset voltage
• 200V/mV gain
• 90dB CMRR
• ±15VDC supply voltage
• 0°C to +70°C
• DIL-8 case
• Large input voltage range
• No latch-up
• High gain
• short-circuit protection
• No frequency compensation required

This JFET operational amplifier is a low power amplifier that features high input impedance, wide bandwidth, high slew rate, and low input offset and input bias currents.

• Very low power consumption
• Dual amplifiers
• Wide common-mode and differential voltage ranges
• Output short-circuit protection
• Internal frequency compensation
• 1MHz Bandwidth
• 6V/mV Gain
• JFET Input
• 76dB CMRR
• 6 to 36V Supply voltage
• 0°C to +70°C
• DIL-8 Case

A low noise Bi-FET quad operational amplifier that incorporates well-matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit.

• 3MHz Bandwidth
• 13V/us Slew rate
• 3mV Input offset voltage
• 200V/mV Gain
• JFET Input
• 86dB CMRR
• 6 to 36V Supply voltage
• 0°C to +70°C
• DIL-14 Case