This Scotch-Weld™ EPX mixing nozzle works with 3M Duo-Pak cartridges to provide thorough mixing and precise placement for easy, uniform application. The tapered tip can be cut to produce a precise bead size.

The nozzle minimizes adhesive waste - simply store any leftover adhesive with the used nozzle in place to provide a good seal. When you're ready, replace it with a new nozzle to continue to use the remaining adhesive in the cartridge.

• Mixing ratios: 1:1, 2:1
• For 48.5 and 50ml syringes
• Colour:green
• Provides thorough mixing and precise placement of two-component structural adhesives
• Tapered tip can be cut to control bead size
• Used nozzle can be left on cartridge to provide a good seal until ready to continue dispensing using a new nozzle
• Supplied singly
• 3M type 7100104991

This Scotch-Weld™ EPX mixing nozzle works with 3M Duo-Pak cartridges to provide thorough mixing and precise placement for easy, uniform application. The tapered tip can be cut to produce a precise bead size.

The nozzle minimizes adhesive waste - simply store any leftover adhesive with the used nozzle in place to provide a good seal. When you're ready, replace it with a new nozzle to continue to use the remaining adhesive in the cartridge.

• Mixing ratio: 10:1
• For 45ml syringes
• Colour: orange
• Provides thorough mixing and precise placement of two-component structural adhesives
• Tapered tip can be cut to control bead size
• Used nozzle can be left on cartridge to provide a good seal until ready to continue dispensing using a new nozzle
• Supplied singly
• 3M type 7100301496

10:1 ratio mixing nozzles for Loctite 3038 and other Loctite acrylic adhesives.

• The nozzles force correct proportions of un-mixed two-part adhesive through a matrix which combines them until they emerge thoroughly mixed at the tip, ready for use
• Supplied in packs of 10
• Loctite type IDH 1034575

Flexible polypropylene dispensing tips for accurate application of Loctite single-part adhesives.

Dispensing tips are colour-coded to indicate the inner diameter of the needle. All tips have a helical thread and can be attached to all Loctite valves via an adaptor. They can also be attached to most Loctite adhesive bottles and syringes to improve dispensing control.

• Size 15
• Colour: amber
• Made from polypropylene
• Flexible head
• Luer-Lock connection
• Colour indicates inner diameter of needle
• Supplied in packs of 50
• Loctite type 97229 (IDH 142640)

Flexible polypropylene dispensing tips for accurate application of Loctite single-part adhesives.

Dispensing tips are colour-coded to indicate the inner diameter of the needle. All tips have a helical thread and can be attached to all Loctite valves via an adaptor. They can also be attached to most Loctite adhesive bottles and syringes to improve dispensing control.

• Size 18
• Colour: green
• Made from polypropylene
• Flexible head
• Luer-Lock connection
• Colour indicates inner diameter of needle
• Supplied in packs of 50
• Loctite type 97230 (IDH 142641)

Flexible polypropylene dispensing tips for accurate application of Loctite single-part adhesives.

Dispensing tips are colour-coded to indicate the inner diameter of the needle. All tips have a helical thread and can be attached to all Loctite valves via 97233 (IDH 88672) Luer-Lock adaptor, 87-7407. They can also be attached to most Loctite adhesive bottles and syringes to improve dispensing control.

• Size 20
• Colour: pink
• Made from polypropylene
• Flexible head
• Luer-Lock connection
• Colour indicates inner diameter of needle
• Supplied in packs of 50
• Loctite type 97231 (IDH 142642)

Flexible polypropylene dispensing tips for accurate application of Loctite single-part adhesives.

Dispensing tips are colour-coded to indicate the inner diameter of the needle. All tips have a helical thread and can be attached to all Loctite valves via an adaptor. They can also be attached to most Loctite adhesive bottles and syringes to improve dispensing control.

• Size 25
• Colour: red
• Made from polypropylene
• Flexible head
• Luer-Lock connection
• Colour indicates inner diameter of needle
• Supplied in packs of 50
• Loctite type 97232 (IDH 142643)

Mixing nozzles for Loctite 3090 two-component syringes and cartridges.

• The nozzles force correct proportions of un-mixed two-part adhesives through a matrix which combines them until they emerge thoroughly mixed at the tip, ready for use
• Supplied in packs of 10
• Loctite type IDH 1453183

A mixing nozzle for 200/400ml two-component epoxy and PU syringes and cartridges.

• The nozzles force correct proportions of un-mixed two-part adhesives through a matrix which combines them until they emerge thoroughly mixed at the tip, ready for use
• Supplied in packs of 10
• Loctite type 984570 (IDH 1487439)

A mixing nozzle for 400ml two-component epoxy and PU syringes and cartridges.

• The nozzles force correct proportions of un-mixed two-part adhesives through a matrix which combines them until they emerge thoroughly mixed at the tip, ready for use
• Supplied in packs of 10
• Loctite type IDH 1573135

A mixing nozzle for 50ml two-component epoxy and PU syringes and cartridges.

• The nozzles force correct proportions of un-mixed two-part adhesives through a matrix which combines them until they emerge thoroughly mixed at the tip, ready for use
• Supplied in packs of 10
• Loctite type IDH 1823921

The Loctite 218288, 97262, 24-piece assortment kit contains 2 each of the following needles: 97221, 97222, 97223, 97224, 97225, 97226, 97227, 97228, 97229, 97230, 97231 and 97232.

• Single-part adhesive needles
• Assortment of various sized needles
• Colour indicates inner diameter of needle
• Assorted 24-piece kit
• See Technical Details for kit contents
• Loctite type 97262 (IDH 218288)

Dispensing tips / dosing nozzles for precise application of Loctite adhesives and activators.

Dispensing tips are colour-coded to indicate the inner diameter of the needle. All tips have a helical thread and can be attached to all Loctite valves via 97233 (IDH 88672) Luer-Lock adaptor (87-7407). They can also be attached to most Loctite adhesive bottles and syringes to improve dispensing control.

• 0.6mm (20 gauge)
• All-plastic construction
• Supplied in packs of 50
• Loctite type 97290 (IDH 397462)

Tapered dispensing tips for accurate application of Loctite single-part adhesives.

Dispensing tips are colour-coded to indicate the inner diameter of the needle. All tips have a helical thread and can be attached to all Loctite valves via 97233 (IDH 88672) Luer-Lock adaptor, 87-7407. They can also be attached to most Loctite adhesive bottles and syringes to improve dispensing control.

• 16 gauge
• Colour: grey
• Length: 30mm
• Made from polyethylene
• Tapered head
• Luer-Lock connection
• Colour indicates inner diameter of needle
• Supplied in packs of 50
• Loctite type 97221 (IDH 88660)

Tapered dispensing tips for accurate application of Loctite single-part adhesives.

Dispensing tips are colour-coded to indicate the inner diameter of the needle. All tips have a helical thread and can be attached to all Loctite valves via an adaptor, They can also be attached to most Loctite adhesive bottles and syringes to improve dispensing control.

• 18 gauge
• Colour: green
• Length: 30mm
• Made from polyethylene
• Tapered head
• Luer-Lock connection
• Colour indicates inner diameter of needle
• Supplied in packs of 50
• Loctite type 97222 (IDH 88661)

Tapered dispensing tips for accurate application of Loctite single-part adhesives.

Dispensing tips are colour-coded to indicate the inner diameter of the needle. All tips have a helical thread and can be attached to all Loctite valves via an adaptor, They can also be attached to most Loctite adhesive bottles and syringes to improve dispensing control.

• 20 gauge
• Colour: pink
• Length: 30mm
• Made from polyethylene
• Tapered head
• Luer-Lock connection
• Colour indicates inner diameter of needle
• Supplied in packs of 50
• Loctite type 97223 (IDH 88662)

Tapered dispensing tips for accurate application of Loctite single-part adhesives.

Dispensing tips are colour-coded to indicate the inner diameter of the needle. All tips have a helical thread and can be attached to all Loctite valves via an adaptor. They can also be attached to most Loctite adhesive bottles and syringes to improve dispensing control.

• 22 gauge
• Colour: blue
• Length: 30mm
• Made from polyethylene
• Tapered head
• Luer-Lock connection
• Colour indicates inner diameter of needle
• Supplied in packs of 50
• Loctite type 97224 (IDH 88663)

Stainless steel dispensing tips for accurate application of Loctite single-part adhesives.

Dispensing tips are colour-coded to indicate the inner diameter of the needle. All tips have a helical thread and can be attached to all Loctite valves via 97233 (IDH 88672) Luer-Lock adaptor, 87-7407. They can also be attached to most Loctite adhesive bottles and syringes to improve dispensing control.

• Size 15
• Colour: amber
• Made from stainless steel
• Luer-Lock connection
• Colour indicates inner diameter of needle
• Supplied in packs of 50
• Loctite type 97225 (IDH 88664)

Stainless steel dispensing tips for accurate application of Loctite single-part adhesives.

Dispensing tips are colour-coded to indicate the inner diameter of the needle. All tips have a helical thread and can be attached to all Loctite valves via 97233 (IDH 88672) Luer-Lock adaptor, 87-7407. They can also be attached to most Loctite adhesive bottles and syringes to improve dispensing control.

• Size 18
• Colour: green
• Made from stainless steel
• Luer-Lock connection
• Colour indicates inner diameter of needle
• Supplied in packs of 50
• Loctite type 97226 (IDH 88665)

Stainless steel dispensing tips for accurate application of Loctite single-part adhesives.

Dispensing tips are colour-coded to indicate the inner diameter of the needle. All tips have a helical thread and can be attached to all Loctite valves via 97233 (IDH 88672) Luer-Lock adaptor, 87-7407. They can also be attached to most Loctite adhesive bottles and syringes to improve dispensing control.

• Size 20
• Colour: pink
• Made from stainless steel
• Luer-Lock connection
• Colour indicates inner diameter of needle
• Supplied in packs of 50
• Loctite type 97227 (IDH 88666)

Stainless steel dispensing tips for accurate application of Loctite single-part adhesives.

Dispensing tips are colour-coded to indicate the inner diameter of the needle. All tips have a helical thread and can be attached to all Loctite valves via 97233 (IDH 88672) Luer-Lock adaptor, 87-7407. They can also be attached to most Loctite adhesive bottles and syringes to improve dispensing control.

• Size 25
• Colour: red
• Made from stainless steel
• Luer-Lock connection
• Colour indicates inner diameter of needle
• Supplied in packs of 50
• Loctite type 97228 (IDH 88667)

These adaptors allow Loctite dispensing needles to be attached to Loctite valves.

• Luer-lock adaptor kit
• 20x Luer-locks
• 5x adaptors
• Loctite type 97233 (IDH 88672)

A 14-gauge dispensing needle tip from the Metcal TE series. The needle tip consists of a stainless-steel cannula with a double-helix polypropylene hub.

This premier quality dispensing needle is burr-free with an electro-polished cannula for unobstructed and consistent material flow.

• 14-gauge
• Length 12.7mm (½in.)
• Silicone and chloride free
• Supplied in packs of 50
• Metcal type 914050-TE

A 15-gauge dispensing needle tip from the Metcal TE series. The needle tip consists of a stainless-steel cannula with a double-helix polypropylene hub.

This premier quality dispensing needle is burr-free with an electro-polished cannula for unobstructed and consistent material flow.

• 15-gauge
• Length 12.7mm (½in.)
• Silicone and chloride free
• Supplied in packs of 50
• Metcal type 915050-TE

A 16-gauge DHUV tapered dispensing tip from Metcal. The tip is moulded in high-density polyethylene with a UV light-block additive and includes a double-helix luer lock hub.

• 16-gauge
• Tapered tip prevents blockage and increases flow of high viscosity materials
• Moulded in high density polyethylene
• UV light-block additive
• Length 32mm (1¼in.)
• Supplied in packs of 50
• Metcal type 916125-DHUV

An 18-gauge dispensing needle tip from the Metcal TE series. The needle tip consists of a stainless-steel cannula with a double-helix polypropylene hub.

This premier quality dispensing needle is burr-free with an electro-polished cannula for unobstructed and consistent material flow.

• 18-gauge
• Length 12.7mm (½in.)
• Silicone and chloride free
• Supplied in packs of 50
• Metcal type 918050-TE

An 18-gauge DHUV tapered dispensing tip from Metcal. The tip is moulded in high-density polyethylene with a UV light-block additive and includes a double-helix luer lock hub.

• 18-gauge
• Tapered tip prevents blockage and increases flow of high viscosity materials
• Moulded in high density polyethylene
• UV light-block additive
• Length 32mm (1¼in.)
• Supplied in packs of 50
• Metcal type 918125-DHUV

A 20-gauge dispensing needle tip from the Metcal TE series. The needle tip consists of a stainless-steel cannula with a double-helix polypropylene hub.

This premier quality dispensing needle is burr-free with an electro-polished cannula for unobstructed and consistent material flow.

• 20-gauge
• Length 12.7mm (½in.)
• Silicone and chloride free
• Supplied in packs of 50
• Metcal type 920050-TE

A 20-gauge DHUV tapered dispensing tip from Metcal. The tip is moulded in high-density polyethylene with a UV light-block additive and includes a double-helix luer lock hub.

• 20-gauge
• Tapered tip prevents blockage and increases flow of high viscosity materials
• Moulded in high density polyethylene
• UV light-block additive
• Length 32mm (1¼in.)
• Supplied in packs of 50
• Metcal type 920125-DHUV

A 21-gauge dispensing needle tip from the Metcal TE series. The needle tip consists of a stainless-steel cannula with a double-helix polypropylene hub.

This premier quality dispensing needle is burr-free with an electro-polished cannula for unobstructed and consistent material flow.

• 21-gauge
• Length 12.7mm (½in.)
• Silicone and chloride free
• Supplied in packs of 50
• Metcal type 921050-TE

A 22-gauge dispensing needle tip from the Metcal TE series. The needle tip consists of a stainless-steel cannula with a double-helix polypropylene hub.

This premier quality dispensing needle is burr-free with an electro-polished cannula for unobstructed and consistent material flow.

• 22-gauge
• Length 12.7mm (½in.)
• Silicone and chloride free
• Supplied in packs of 50
• Metcal type 922050-TE

A 23-gauge dispensing needle tip from the Metcal TE series. The needle tip consists of a stainless-steel cannula with a double-helix polypropylene hub.

This premier quality dispensing needle is burr-free with an electro-polished cannula for unobstructed and consistent material flow.

• 23-gauge
• Length 12.7mm (½in.)
• Silicone and chloride free
• Supplied in packs of 50
• Metcal type 923050-TE

A 25-gauge dispensing needle tip from the Metcal TE series. The needle tip consists of a stainless-steel cannula with a double-helix polypropylene hub.

This premier quality dispensing needle is burr-free with an electro-polished cannula for unobstructed and consistent material flow.

• 25-gauge
• Length 12.7mm (½in.)
• Silicone and chloride free
• Supplied in packs of 50
• Metcal type 925050-TE

A 27-gauge dispensing needle tip from the Metcal TE series. The needle tip consists of a stainless-steel cannula with a double-helix polypropylene hub.

This premier quality dispensing needle is burr-free with an electro-polished cannula for unobstructed and consistent material flow.

• 27-gauge
• Length 12.7mm (½in.)
• Silicone and chloride free
• Supplied in packs of 50
• Metcal type 927050-TE

A 30-gauge dispensing needle tip from the Metcal TE series. The needle tip consists of a stainless-steel cannula with a double-helix polypropylene hub.

This premier quality dispensing needle is burr-free with an electro-polished cannula for unobstructed and consistent material flow.

• 30-gauge
• Length 12.7mm (½in.)
• Silicone and chloride free
• Supplied in packs of 50
• Metcal type 930050-TE

A stainless steel dispensing needle, also commonly referred to as a dispensing nib or tip. This plastic-hubbed needle is ideal for precise application of a variety of medium viscosity fluids.

• Size 14 gauge
• Length 12.7mm
• Supplied in packs of 50
• Weller type KDS1412P series

A stainless steel dispensing needle, also commonly referred to as a dispensing nib or tip. This plastic-hubbed needle is ideal for precise application of a variety of medium viscosity fluids.

• Size 14 gauge
• Length 25.4mm
• Supplied in packs of 50
• Weller type KDS141P series

A 14 gauge dispensing needle, also commonly referred to as a dispensing nib or tip. This smooth-flow tapered needle is ideal for high viscosity fluids.

• Size 14 gauge
• Length 38.1mm (1.5in.)
• Taper reduces dripping from needle
• Plastic material doesn't scratch delicate surfaces
• Supplied in packs of 50
• Weller type KDS14TNP

A stainless steel dispensing needle, also commonly referred to as a dispensing nib or tip. This plastic-hubbed needle is ideal for precise application of a variety of medium viscosity fluids.

• Size 15 gauge
• Length 12.7mm
• Supplied in packs of 50
• Weller type KDS1512P series

A stainless steel dispensing needle, also commonly referred to as a dispensing nib or tip. This plastic-hubbed needle is ideal for precise application of a variety of medium viscosity fluids.

• Size 16 gauge
• Length 38.1mm
• Supplied in packs of 50
• Weller type KDS16112P series

A stainless steel dispensing needle, also commonly referred to as a dispensing nib or tip. This plastic-hubbed needle is ideal for precise application of a variety of medium viscosity fluids.

• Size 16 gauge
• Length 12.7mm
• Supplied in packs of 50
• Weller type KDS1612P series

A stainless steel dispensing needle, also commonly referred to as a dispensing nib or tip. This plastic-hubbed needle is ideal for precise application of a variety of medium viscosity fluids.

• Size 16 gauge
• Length 25.4mm
• Supplied in packs of 50
• Weller type KDS161P series

A 16 gauge dispensing needle, also commonly referred to as a dispensing nib or tip. This smooth-flow tapered needle is ideal for high viscosity fluids.

• Size 16 gauge
• Length 38.1mm (1.5in.)
• Taper reduces dripping from needle
• Plastic material doesn't scratch delicate surfaces
• Supplied in packs of 50
• Weller type KDS16TNP

A stainless steel dispensing needle, also commonly referred to as a dispensing nib or tip. This plastic-hubbed needle is ideal for precise application of a variety of medium viscosity fluids.

• Size 17 gauge
• Length 12.7mm
• Supplied in packs of 50
• Weller type KDS1712P series

A stainless steel dispensing needle, also commonly referred to as a dispensing nib or tip. This plastic-hubbed needle is ideal for precise application of a variety of medium viscosity fluids.

• Size 18 gauge
• Length 12.7mm
• Supplied in packs of 50
• Weller type KDS1812P series

A stainless steel dispensing needle, also commonly referred to as a dispensing nib or tip. This plastic-hubbed needle is ideal for precise application of a variety of medium viscosity fluids.

• Size 18 gauge
• Length 25.4mm
• Supplied in packs of 50
• Weller type KDS181P series

An 18 gauge dispensing needle, also commonly referred to as a dispensing nib or tip. This smooth-flow tapered needle is ideal for high viscosity fluids.

• Size 18 gauge
• Length 38.1mm (1.5in.)
• Taper reduces dripping from needle
• Plastic material doesn't scratch delicate surfaces
• Supplied in packs of 50
• Weller type KDS18TNP

A stainless steel dispensing needle, also commonly referred to as a dispensing nib or tip. This plastic-hubbed needle is ideal for precise application of a variety of medium viscosity fluids.

• Size 19 gauge
• Length 12.7mm
• Supplied in packs of 50
• Weller type KDS1912P series

A stainless steel dispensing needle, also commonly referred to as a dispensing nib or tip. This plastic-hubbed needle is ideal for precise application of a variety of medium viscosity fluids.

• Size 19 gauge
• Length 25.4mm
• Supplied in packs of 50
• Weller type KDS191P series

A stainless steel dispensing needle, also commonly referred to as a dispensing nib or tip. This plastic-hubbed needle is ideal for precise application of a variety of medium viscosity fluids.

• Size 20 gauge
• Length 12.7mm
• Supplied in packs of 50
• Weller type KDS2012P series