3M™ Scotch-Weld™ DP100 is a fast-setting 2-part epoxy adhesive which delivers a wide range of benefits, including easy mixing, fast cure, rigid bonds and low viscosity. It provides a strong, permanent bond even under vibration and impact, high shear and peel strength and handling strength in approximately 15 minutes at room temperature.

DP100 makes bonding and joining, glueing and attaching, assembling and sealing, encapsulating and potting a much easier process.

• Very flexible
• Dries and stays clear even when cured in larger masses
• Supplied in 50ml dispenser
• Manufacturer's part 7000080310

Scotch-Weld™ DP490 EPX from 3M™ is a high performance black thixotropic two-component epoxy adhesive with particularly good application characteristics. It is ideal for use where toughness and high strength are required and shows special benefits in the construction of composite assemblies.

• Suitable for gap filling
• Excellent heat and environmental resistance
• Supplied in dispenser of 50ml
• Manufacturer's part 7000006833

A two part epoxy resin glue made by Araldite, which will bond ceramics, wood, chipboard, glass, metal and most hard plastics.

• Extra strong, long lasting bond
• Repositionable for up to two hours
• Solvent free
• Supplied with one tube of adhesive and one tube of hardener
• Syringe enables equal amounts of resin and hardener to be dispensed
• Syringe features re-usable cap
• Glue will not dry out in tubes
• Supplied in 2x 15ml tubes

A two part epoxy resin glue made by Araldite, which will bond ceramics, wood, chipboard, glass, metal and most hard plastics.

• Extra strong, long lasting bond
• Repositionable for up to two hours
• Solvent free
• Supplied with one tube of adhesive and one tube of hardener
• Syringe enables equal amounts of resin and hardener to be dispensed
• Syringe features re-usable cap
• Glue will not dry out in tubes
• Supplied in a 24ml dual syringe

Araldite Rapid glue is a quick-setting version of the famous two-part epoxy adhesive, which bonds ceramics, wood, chipboard, glass, metal and most hard plastics. This specially formulated type of Araldite glue is a two-part fast setting epoxy adhesive prepared by mixing equal parts of resin and hardener. It is then applied to the parts to be joined and allowed to cure.

• Fast setting and very strong
• Solvent free
• Heat, cold, water and oil resistant
• Sets with virtually no shrinkage and joints are resistant to chemical attack
• Provides a seal which is impervious to moisture
• Ideal for electrically insulating and a protection against electrolytic corrosion
• Araldite Rapid is supplied in 2x 15ml tubes (one tube of adhesive and one tube of hardener)

Araldite Epoxy rapid glue is a quick-setting version of the famous two-part epoxy adhesive, which bonds ceramics, wood, chipboard, glass, metal and most hard plastics. This specially formulated type of Araldite glue is a two-part fast setting epoxy adhesive prepared by mixing equal parts of resin and hardener. It is then applied to the parts to be joined and allowed to cure. The syringe pack simplifies the Araldite glue measuring process by automatically dispensing the correct quantities of resin and hardener.

• Fast setting and very strong
• Solvent free
• Heat, cold, water and oil resistant
• Sets with virtually no shrinkage and joints are resistant to chemical attack
• Provides a seal which is impervious to moisture
• Ideal for electrically insulating and a protection against electrolytic corrosion
• Araldite Rapid is supplied in a 24ml dual syringe

Araldite® is a strong, long lasting solvent-free epoxy adhesive which is water resistant and is ideal for metal repair jobs such as plumbing, car bodywork, metal gates and windows. Bonds most metals including cast iron, steel, copper, brass and aluminium. The finished product can be painted or sanded.

• Will not rust
• Metallic grey colour
• Parts repositionable for 4 minutes
• Oil, chemical and impact resistant
• High temperature resistance (-30° to 65°C)
• Supplied in two 15ml tubes with spatula and mixing tray
• Manufacturer's part ARA-400010

Note: Not suitable for use with items that will contact foodstuffs.

Instant clear is a strong, long lasting adhesive, which sets in 90 seconds.

• Ideal for uneven breaks
• Sets clear
• Bonds china, glassware, leather, fabric, cardboard, wood and most hard plastics
• Ideal for all household repairs
• Syringe pack for easy mixing
• Syringe enables equal amounts of resin and hardener to be dispensed and features a resealable cap
• Glue will not dry out in tubes
• Supplied in 24ml dual syringe

Araldite® Repair filling is a hard, long-lasting repair putty which bonds firmly to most materials. It is ideal for repairs to metal pipework, water tanks and radiators and for making good tools and other equipment. This solvent-free multipurpose putty sets extremely hard after 72 hours, after which it can be drilled or sanded.

• Sets in wet conditions
• Water, oil, chemical and impact resistant
• High temperature resistance (-40° to 120°C)
• Withstands rough handling
• Hardens after 10 minutes; fully cured in 72 hours
• Supplied in 50g bars
• Manufacturer's part ARA-400015

Note: Not suitable for use with items that will contact foodstuffs.

Araldite 2014-2 is a two component, room temperature curing, thixotropic paste adhesive of high strength with good environmental and excellent chemical resistance. Used for bonding of metals, electronic components, GRP structures and many other items where a higher than normal temperature or more aggressive environment is to be encountered in service.

Araldite 2014-2 is a more user-friendly and sustainable product, equivalent in performance to Araldite 2014-1, 87-0272.

• Grey paste
• High temperature and chemical resistance
• Very resistant to water and to a wide variety of chemicals
• Gap-filling, non sagging up to 5mm thickness
• Supplied in a twin syringe
• Volume: 200ml
• Araldite type 2014-2

Araldite 2014-2 is a two component, room temperature curing, thixotropic paste adhesive of high strength with good environmental and excellent chemical resistance. Used for bonding of metals, electronic components, GRP structures and many other items where a higher than normal temperature or more aggressive environment is to be encountered in service.

Araldite 2014-2 is a more user-friendly and sustainable product, equivalent in performance to Araldite 2014-1, 87-0272.

• Grey paste
• High temperature and chemical resistance
• Very resistant to water and to a wide variety of chemicals
• Gap-filling, non sagging up to 5mm thickness
• Supplied in a twin syringe
• Volume: 50ml
• Araldite type 2014-2

Bondloc B2001 is a hand kneadable, specialty epoxy putty that mixes for permanent repairs to many substrates. Contains fading black dye that becomes grey after mixing. May be applied under water (fresh or salt). Bonds to fibreglass, metal, wood, concrete and glass. Will not yellow to UV exposure. Hardens in 10 minutes, back in service in an hour, full strength in 24 hours.

Can be used for repairing tanks and drums, patching holes in pipes, stopping leaks and repairing porosity holes in castings.

Specification:

Typical Properties: 7 days cured at 24°CColour: Black, changes to grey after mixingViscosity: putty/hand kneadablePot Life @24°C: 20 minutesComprehensive Strength: 83 N/mm2Adhesive Tensile Shear: 5 N/mm2Cured Hardness Shore: D 75Dielectric Strength: volts/mil 300Solids: 100%Temperature Resistance: Wet: 49°C, Dry: 121°CSize: 50g

Bondloc B2012 is a 2-part, rapid cold curing epoxy adhesive, that is suitable for bonding a wide variety of surfaces including steel, aluminium and galvanised iron. Reacts within a few minutes to give a tough, resilient bond on a wide variety of surfaces.

Specifications:

Mix Ratio: 1:1Work Life: As a mix: 4 1/2 - 5 minutesSize: 25ml

Part 1

Physical Form: Viscous liquidChemical Type: EpoxyAppearance: ClearViscosity 25°C: 100 poiseSpecific Gravity: 1.17

Part 2

Physical Form: Viscous liquidChemical Type: Mercaptan and PolyamideAppearance: ClearViscosity 25°C: 130 poiseSpecific Gravity: 1.14

Bondloc B2013 is a steel-filled epoxy putty for general maintenance, repairs, filling, rebuilding and bonding metal surfaces.

Specifications:

Colour: BlackMixed Viscosity: Putty% Solids by Volume: 100Cured Density: 2.33 gm/ccCure Shrinkage ASTM D2566: 0.0006 in/inSpecific Volume: 11.9 in/lbPot Life: 45 minutesComprehensive Strength ASTM D695: 8,260 PSIAdhesive Tensile Strength EASTMD1002: 2,800 PSICured Hardness Shore D ASTM 2240: 85 DDielectric Strength volts/mil ASTM D149: 30Coverage: 48 sq.in/lb @ 1/4inTemperature Resistance: Wet: 100°F, Dry: 250°FSize: 25ml

Bondloc B2060 is a 60 second, 2-part, rapid cold curing epoxy adhesive. It is suitable for bonding a wide variety of surfaces including steel, aluminium and galvanised iron. It reacts within a minute to give a tough resilient bond on a wide variety of surfaces.

Specifications:

Mix Ratio 1:1Work Life as a Mix: 40 - 70 secondsSize: 25ml

Part 1

Physical Form: Viscous liquidChemical Type: EpoxyAppearance: ClearViscosity @ 25°C: 100 poiseSpecific Gravity: 1.17

Part 2

Physical Form: Viscous liquidChemical Type: Mercaptan and PolyamideAppearance: BlueViscosity @ 25°C: 130 PoiseSpecific Gravity: 1.14

Bondloc B3294 is a toughened structural adhesive formulated for bonding dissimilar substrates as well as unprepared metals, ceramics, wood, concrete and standard thermoset plastics. The final adhesive bond is designed to be load-bearing and resistant to weathering, humidity and wide temperature variations.

Applications: Outdoor weathering or solvent exposure thermoformed plastic assemblies, PVC, fibreglass, vinyls, ABS, steel aluminium, stainless steel, acrylics, phenolic, polycarbonate, styrenics, Noryl, PET, wood, concrete and ceramic magnet and speaker assembly.

Specifications:

Viscosity: 55,000cpsColour: Off whiteWeight: 8.44 lbs/galMixed Density: 8.28lbs/galFlash Point: 51°FMixed Viscosity: No sagging gelOpen Time: 3 minutes @ 72°F, 22°CAssembly Time: 6 minutes @ 72°F, 22°CFunctional Cure: 3/4-1 hourFull Cure: 4 hoursSolvents: NoneCoverage: (based on 25ml) 152 sq.in @ 0.010in

Two part, cold curing epoxy resin adhesive. Suitable for bonding a wide range of surfaces including steel, aluminium, and galvanised iron. Reacts within five minutes to give a tough resilient bond. Display packed.

A toughened structural adhesive formulated for bonding differing substrates as well as unprepared metals, ceramics, wood, concrete and standard thermoset plastics. The final adhesive bond is designed to be load bearing and resistant to weathering, humidity and temperature variations. Display packed.

Specialist epoxy putty, ideal for patching holes in fuel tanks, radiators, pipes etc. When mixing, the putty turns a unified colour signifying it's ready for use. Hardens and cures in extreme conditions. Bonds to metal, fibreglass, wood, concrete and glass. Display packed.

Stick 2 Rapid Epoxy Syringe is an industrial strength, two part clear adhesive from Everbuild which sets hard in just 4 minutes. It will bond metals, crockery, glass, wood, concrete, rubber, fabrics, crystal, jewellery and various hard plastics and once cured may be drilled, sanded or painted.

Stick 2 Rapid Epoxy Tube is an industrial strength, two part clear adhesive system which sets hard in just 4 minutes. Ideal for bonding most materials and once cured can be drilled, sanded and painted. For industry and home.

Evo-Stik Rapid Metal is an ultra-strong two-part epoxy adhesive that gives a strong bond in 5 minutes. It is ideal for use on almost all metals including iron, steel, aluminium, copper and brass. Evo-Stik epoxy two-part adhesive is incredibly strong, is solvent-free and heat, water and oil resistant. When dry, Evo-Stik Rapid Metal can be sanded and painted if required.

• 2-part epoxy resin
• Sets in 5 minutes
• Use on almost all metals including iron, steel, aluminium, copper and brass
• Solvent-free
• Heat, water and oil resistant
• Can be sanded and painted when dry
• Supplied in 2x 15ml tubes with spatula and tray for mixing

Evo-Stik Rapid Set is an ultra-strong two-part epoxy adhesive that gives a strong bond in seconds and sets in 5 minutes. It is ideal for use on ceramics, wood, chipboard, glass, metal, stone and most hard plastics.

• 2-part epoxy resin
• Strong bond in seconds
• Sets in 5 minutes
• Use on ceramics, wood, chipboard, glass, metal, stone and most hard plastics
• Supplied in 2x 15ml tubes with spatula and tray for mixing

Evo-Stik Rapid Set is an ultra-strong two-part epoxy adhesive that gives a strong bond in seconds and sets in 5 minutes. It is ideal for use on ceramics, wood, chipboard, glass, metal, stone and most hard plastics.

• 2-part epoxy resin
• Strong bond in seconds
• Sets in 5 minutes
• Use on ceramics, wood, chipboard, glass, metal, stone and most hard plastics
• Supplied in a twin 25ml syringe with spatula and tray for mixing and a resealable cap

Evo-Stik Express is an ultra-strong two-part epoxy adhesive that gives a strong bond in seconds and is clear when set. It is ideal for use on glass and ceramics, where it can provide an 'invisible' bond or mend.

Evo-Stik Express is supplied in a dual 25ml syringe that helps you mix exactly equal amounts of resin and hardener.

• 2-part epoxy resin
• Strong bond in seconds
• Sets clear in 90 seconds
• Use on glass and ceramics for an 'invisible' bond
• Supplied in a twin 25ml syringe with spatula and tray for mixing and a resealable cap

Evo-Stik Power is an ultra-strong two-part epoxy adhesive that gives a strong bond in 80 seconds. It is ideal for use on wood, metal, ceramics, glass, plastic and stone. Evo-Stik epoxy two-part adhesive is incredibly strong, is solvent-free and heat, water and oil resistant. When dry, the resin can be sanded and painted if required. Evo-Stik Power is supplied in a one-shot, dual syringe with a self-mixing nozzle for precise, mess-free mixing.

• 2-part epoxy resin
• Bonds in 80 seconds
• Use on wood, metal, ceramics, glass, plastic and stone
• Solvent-free
• Heat, water and oil resistant
• Can be sanded and painted when dry
• Supplied in a 3g one-shot, dual syringe with a self-mixing nozzle for precise, mess-free mixing

This steel-reinforced epoxy putty from Evo-Stik is ideal for use with metal and a host of other materials. Setting hard in just 10 minutes, this Hard & Fast putty can be drilled, tapped, filed and painted once dry. It can also be used underwater.

• Supplied in tube of 50g
• Manufacturer's part 320123

This 2-part epoxy syringe 25ml from Gorilla Glue is not only king of the adhesive jungle, but one of the quickest setting glues.

Strong, flexible and ideal for a wide range of uses, such as fixing buckles, curtain hooks, tool handles and jewellery. The syringe nozzle also allows for accurate application and comes with a cap for multiple uses.

The epoxy fills voids and bonds uneven and vertical surfaces, while the 5-minute set time allows time for repositioning. Additionally withstands moderate exposure to water and will not break down from exposure to common solvents.

• Long-term effect - sticks for years!
• Ideal for clean, easy finishing
• Dries crystal clear
• Structural gap filler
• Bonds most things
• Reusable syringe
• Low VOC
• Non-toxic once cured
• Manufacturer's part 2044100

Loctite EA 3430 is a five-minute, 2-component epoxy adhesive that produces an optically clear bond line. It develops high strength on a wide range of substrates and is water-resistant. Loctite 3430 is a general-purpose bonder and is ideal for many DIY applications. Due to the very clear bond line, it is also the product of choice for bonding glass, decorative panels and displays. Medium viscosity and fast fixture time at room temperature ensure easy application.

• Easy and fast to apply at room temperature
• Ultra-clear bond line
• Water resistant
• General purpose bonder suitable for a wide range of substrates
• Colour: Ultra clear
• Working life: 7 minutes
• Fixture time: 15 minutes
• Service temperature range: -55 to +100°C
• Tensile strength 22N/mm²
• Peel strength 3N/mm
• Mix ratio by volume: 01:01
• Supplied in a 24ml twin syringe
• Loctite type EA 3430

Loctite EA 3450 is a 2-component epoxy, metal-bonding adhesive with structural characteristics. If you need a reliable solution for bonding or repairing of metal parts, this adhesive is the one for you. It has gap filling properties for rough and poorly fitting surfaces such as metal, ceramic, rigid plastics or wood.

Loctite 3450 cures rapidly at room temperature, is easy to apply and develops high bond strength. Applications include bonding aluminium window frames and GRP panels.

• Two-component epoxy adhesive
• Colour: Grey
• Easy and fast to apply at room temperature
• Ideal for repairing and bonding metal parts
• Develops high bond strength
• Working life: 4 to 6 minutes
• Fixture time: 15 minutes
• Suitable for: Steel and castings
• Viscosity: 35 Pas
• Service temperature range: -55 to +100°C
• Tensile strength 25N/mm²
• Peel strength 1.5N/mm
• Supplied in a 25ml twin syringe
• Loctite type EA 3450

Loctite 3479 is an aluminium-filled, two-component epoxy adhesive that is ideal for the repair and recovery of worn and damaged machinery. Typical applications include repairing worn parts such as shafts, housings, keyways and flanges as well as broken or damaged parts such as castings, pipes or fabrications.

Loctite 3479 can be used for jobs as varied as filling cavities, levelling machinery, repairing cast-steel plates, making core moulds, applying a sacrificial coating or sealing leaking pipes. It is typically used in applications with an operating range of -20 to +190°C.

• Repair aluminium castings, cracked or worn aluminium parts and stripped aluminium threads
• Working life: 40 minutes
• Fixture time: 150 minutes
• Shear strength (GBMS): 20N/mm²
• Compressive strength: 90 N/mm²
• Service temperature range: -20 to +190°C
• Supplied in a 500g tub kit
• Loctite type 3479

Loctite EA 3430 is a five-minute, 2-component epoxy adhesive that produces an optically clear bond line. It develops high strength on a wide range of substrates and is water-resistant. Loctite 3430 is a general-purpose bonder and is ideal for many DIY applications. Due to the very clear bond line, it is also the product of choice for bonding glass, decorative panels and displays. Medium viscosity and fast fixture time at room temperature ensure easy application.

• Easy and fast to apply at room temperature
• Ultra-clear bond line
• Water resistant
• General purpose bonder suitable for a wide range of substrates
• Colour: Ultra clear
• Working life: 7 minutes
• Fixture time: 15 minutes
• Service temperature range: -55 to +100°C
• Tensile strength 22N/mm²
• Peel strength 3N/mm
• Mix ratio by volume: 01:01
• Supplied in a 50ml twin syringe
• Loctite type EA 3430

This fast-curing toughened industrial grade epoxy adhesive from Loctite is ideal for the bonding and potting of components such as sensors and lenses. With a working time before cure of three minutes it is ideal for bonding quick and easy fitting metal and glass assemblies which require a fast cure.

• Low viscosity
• Service temperatures up to 80°C
• Ultra clear
• Excellent electrical insulator
• Low shrinkage properties
• Good peel resistance
• Supplied in dual cartridge of 50ml
• Manufacturer's part 2036158

LOCTITE® EA 3478 is a 2-part, ferro-silicon filled epoxy resin system. It is extremely resistant to corrosion, chemical attack and abrasion. It is ideal for restoring parts worn by mechanical and/or corrosion impact.

Helps to restore tolerances to worn shafts, repairing worn keyways and damaged housings, filling pitted surfaces in worn machinery and restoring fit to bearing housings.

• Rebuilds keyways and spline assemblies
• Rebuilds bearings, clamp connections, tensioning elements, gear wheels or bearing seats
• Ferro-silicon filled with outstanding compression strength
• Ideal for renewing surfaces subjected to compression, thrust, impact and harsh environments
• Supplied in 453g container
• Manufacturer's part 2041672

Loctite EA 9492 is a 2-part white epoxy adhesive designed to offer both high chemical resistance and high temperature resistance up to +180°C in structural bonding applications.

Offering very low out-gassing, this is a good general purpose solution for bonding and repairing a wide range of materials.

• Bonds various materials
• Superior thermal shock and impact resistant properties
• Supplied in dual cartridge of 50ml
• Manufacturer's part 2052215

This 2-part grey epoxy adhesive from Loctite is ideal for structural bonding and offers high technical performance. It is thermally conductive and delivers high compression strength and provides a high temperature resistance up to +180°C for heat resistant bonding and filling.

• Ideal for heat dissipation
• Ideal for bonding metal components
• High compression strength
• Supplied in dual cartridge of 50ml
• Manufacturer's part 2053807

This 2-part grey epoxy adhesive from Loctite is ideal for structural bonding and offers high technical performance. It is thermally conductive and delivers high compression strength and provides a high temperature resistance up to +180°C for heat resistant bonding and filling.

• Ideal for heat dissipation
• Ideal for bonding metal components
• High compression strength
• Supplied in dual cartridge of 400ml
• Manufacturer's part 2053807

Loctite EA 9483 is a low viscosity, industrial grade epoxy adhesive. Once mixed, the two-part epoxy cures at room temperature. It is suitable for bonding and potting where optical clarity and high strength are required. Loctite 9483 is ideal for bonding decorative panels and displays.

• Flowable
• Viscosity 7Pa-s
• Ultra clear
• Low moisture absorption
• Working time: 25 to 60 minutes
• Fixture time: 210 minutes
• Tensile strength: 47N/mm²
• Peel strength: 1.5 N/mm
• Service temperature range: -50 to +150°C
• Supplied in a 50ml dual syringe
• Loctite type EA 9483

LOCTITE EA 9489 is a grey, two-part epoxy adhesive formulated for an extended working life of 60 to 120 minutes, allowing plenty of time to adjust parts during assembly.

This toughened product can also be used for repairing strain gauges, sealing seams on fibreglass components, repairing printed circuit boards, bonding stainless steel inserts and rubber hose to steel tubing.

• 2-part epoxy adhesive
• Toughened, general purpose product
• Extended working life
• Medium viscosity
• Flexible bond line
• 50ml dual cartridge
• Loctite type EA 9489

Loctite 9466 is a tough, multi-purpose, industrial grade epoxy adhesive with extended workable life. Once mixed, the two-component epoxy cures at room temperature to form a tough, off-white bond which provides high peel resistance and high shear strength. The fully cured epoxy is resistant to a wide range of chemicals and solvents, and acts as an excellent electrical insulator.

Loctite 9466 provides excellent bond strengths to a wide variety of substrates like metals, ceramic and most plastics. Typical applications include general purpose industrial applications requiring extended work life for adjusting parts during assembly.

• Medium viscosity
• Low density - SG = 1.0
• High strength
• Working time: 60 min.
• Fixture time: 180 min.
• Viscosity in Pa-s: 35
• Tensile strength: 32 N/mm²
• Peel strength: 8 N/mm
• Service temperature range: -55 to +120°C
• Colour mix: off-white
• Supplied in a twin 50ml syringe with mixing nozzle
• Loctite type 9466

Loctite 9466 is a tough, multi-purpose, industrial grade epoxy adhesive with extended workable life. Once mixed, the two-component epoxy cures at room temperature to form a tough, off-white bond which provides high peel resistance and high shear strength. The fully cured epoxy is resistant to a wide range of chemicals and solvents, and acts as an excellent electrical insulator.

Loctite 9466 provides excellent bond strengths to a wide variety of substrates like metals, ceramic and most plastics. Typical applications include general purpose industrial applications requiring extended work life for adjusting parts during assembly.

• Medium viscosity
• Low density - SG = 1.0
• High strength
• Working time: 60 min.
• Fixture time: 180 min.
• Viscosity in Pa-s: 35
• Tensile strength: 32 N/mm²
• Peel strength: 8 N/mm
• Service temperature range: -55 to +120°C
• Colour mix: off-white
• Supplied in 400ml with mixing nozzle
• Loctite type 9466

Loctite EA 9464 is a 2-part, grey structural bonding epoxy adhesive which is fast curing at room temperature and provides a toughened bond. Its thixotropic properties make it good for gap filling.

It is ideal for joining dissimilar substrate materials including metals, engineering thermoplastics and thermoset laminates such as SMC.

• Fast-curing
• Creates a tough bond
• Good choice for dissimilar materials
• High peel and shear strength
• Supplied in dual cartridge of 50ml
• Manufacturer's part 2058065

Loctite EA 9461 is a 2-part grey structural bonding epoxy which cures at room temperature to provide a toughened bond. It is ideal for joining dissimilar substrate materials including metals, engineering thermoplastics and thermoset laminates such as SMC. Its thixotropic properties make it good for gap filling and it provides both high peel and shear strength.

• Thixotropic and non-sagging
• Supplied in 50ml dual cartridge
• Manufacturer's part 2061255

Loctite EA 3425 is a 2-part yellow/white general purpose epoxy adhesive paste ideal for structural bonding and providing high strength adhesion, high modulus and very good chemical resistance. It cures at room temperature and has a medium to long working life.

Its thixotropic properties make it particularly good for bonding metals and large surface areas.

• Non-sag and thixotropic
• Suitable for a range of substrates
• Good choice for metals and large surface areas
• Supplied in dual cartridge of 50ml
• Manufacturer's part 2063045

Loctite EA 3421 is a 2-part, clear amber, general purpose epoxy adhesive which cures slowly at room temperature after mixing. It develops high strength and excellent moisture resistance and its gap filling properties make this adhesive system suitable for rough or poorly fitting surfaces made from metal, ceramic, wood or rigid plastics.

The long working life and medium viscosity make this adhesive system suitable for large surfaces and where adjustment time is needed after assembly.

• Applications include bonding aluminium window frames and GRP panels
• Supplied in dual cartridge of 50ml
• Manufacturer's part 2063254

Loctite EA 3423 structural bonding is a two-component, high viscosity, thixotropic epoxy adhesive that cures at room temperature after mixing. It is a general purpose, non-sag adhesive that develops high strength on a wide range of substrates. Its thixotropic properties enable Loctite 3423 to bond rough vertical surfaces made from metal, ceramic, rigid plastics or wood through gaps of up to 3mm.

When cured, the adhesive can be sanded to a smooth finish. It is ideal for bonding metal components, is excellent for metal and has good humidity resistance.

• Two-component adhesive
• Colour: Grey
• Material suitability: Metal, Ceramic, PVC, Wood
• Non-sag paste
• Excellent chemical resistance
• Working time: 30 to 60 minutes
• Fixture time: 180 minutes
• Viscosity in Pa-s: 300
• Tensile strength: 24 N/mm²
• Peel strength: 2 to 3 N/mm
• Service temperature range: -50 to +120°C
• Supplied in a 50ml cartridge with mixing nozzle
• Loctite type EA 3423

Loctite EA 9514 is a single-part high performance grey epoxy adhesive for structural bonding that is formulated for applications requiring characteristics such as filter and magnet bonding. The product is suitable for gap filling and is resistant to operating temperatures up to +200°C.

• Toughened
• Suitable for induction curing
• High shear and peel strength
• Supplied in cartridge of 300ml
• Manufacturer's part 2065585

This silver coloured metal-filled paste adhesive from Loctite is designed to provide maximum resistance to impact, shear, cleavage and tensile loads. It will bond to a wide variety of surfaces, including oily steel. It can replace traditional fixing techniques for enhanced appearance and greater design flexibility.

• Durability, chemical resistance and high temperature performance are extremely good
• Performance usually limited by the strength of the product adhered to
• Supplied in 320ml container
• Manufacturer's part 2065824

LOCTITE® EA 109 is a cream-coloured, single-part, high temperature, epoxy adhesive designed to provide maximum resistance to impact, shear, cleavage and tensile loads. Best results are achieved by heat curing.

Industry applications include automotive, manufacturing, magnet bonding, filter end-caps, etc.

• Will bond to a wide variety of surfaces, including oily steel
• Performance is usually limited by the strength of the substrates themselves
• Extremely good durability, chemical resistance and high temperature performance
• Can replace traditional fixing techniques to give enhanced appearance and greater design flexibility
• Colour: cream
• Fixture time: 240 minutes
• Fixture time temperature: 240°C
• Shear strength: 30N/mm²
• Technology: epoxy
• Electrically non-conductive
• Service temperature range: -40 to +180°C
• Supplied in a 320ml syringe pack
• Loctite type ESP109

Loctite EA 3475 is a 2-part aluminium-filled epoxy adhesive suited to the repair and recovery of worn and damaged machinery including parts such as shafts, housings, keyways and flanges. It is useful for filling cavities, levelling machinery, repairing cast-steel plates, making core moulds, applying a sacrificial coating or sealing leaking pipes.

• Repairs aluminium castings, cracked/worn aluminium parts and stripped aluminium threads
• Non-sagging
• Easily mixed and moulded to form odd shapes if required
• Cures to a non-rusting, aluminium-like finish
• Supplied in set of 500g
• Manufacturer's part 229173