AC11 is a solvent-based activator formulated to increase the cure speed of cyanoacrylate adhesives. It can be used to give instant 'on demand' curing, and is especially suited to use with slower, high viscosity adhesives, and with porous substrates where the adhesive must cure before being absorbed into the substrate.

• Can also be used to 'fillet cure' and to cure adhesive outside of the joint
• Supplied in 200ml aerosols

PVCu Acti-spray is an aerosol applied activator for use with Everbuild Industrial Superglue GP and HV, setting superglue in 10 seconds. Guaranteed not to stain PVCu. Acti-spray is ideal for use on all PVCu and plastics.

A fast and effective cleaner from Evo-Stik ideal for removing the residue of solvent-based adhesives. Even small areas of old adhesive can be removed with the minimum of effort.

• Designed to tackle wet or dry adhesives
• Ideal for removing grease and wax
• Supplied in 5 litre can
• Manufacturer's part 94604

A fast and effective cleaner from Evo-Stik ideal for removing the residue of solvent-based adhesives.

• Can be used on wet or dry adhesives
• Even small areas of old adhesive can be removed
• Removes grease, wax and similar stains
• Supplied in a 250ml can
• Manufacturer's type 97056

Not suitable for use on polystyrene, cellulose paint, vinyl and rayon fabrics.

This Loctite SF 7649 activator is designed to promote the curing speed of anaerobic adhesives and sealants without any significant loss of joint strength. It is ideal for applications with passive metals or inert surfaces and with large bond gaps and is particularly recommended when the application temperature is below 15 °C.

• Increases cure speed on passive and inactive surfaces
• Suitable for low-temperature curing (< 5°C)
• Supplied in can of 500ml
• Manufacturer's part 135252

Loctite SF 7471 is a transparent, yellow to amber liquid activator used where increased cure speed of anaerobic products is required. It is especially recommended for applications with passive metals or inert surfaces and with large bond gaps and when the prevailing temperature is low (<+15 °C).

• Speeds up cure on passive and active surfaces
• Suitable for large bond gaps
• On-part life ≤7 days
• Supplied in 150ml aerosol
• Manufacturer's part 142468

Loctite SF 7386 is a transparent, yellow to light amber liquid activator designed to initiate the cure of toughened acrylic adhesives. The fixture time and cure speed depend on the adhesive used, the substrate bonded, surface cleanliness and whether one or two-surface activation is used.

• Supplied in 500ml container
• Manufacturer's part 142475

This Loctite SF 7649 activator is designed to promote the curing speed of anaerobic adhesives and sealants without any significant loss of joint strength. It is ideal for applications with passive metals or inert surfaces and with large bond gaps and is particularly recommended when the application temperature is below 15 °C.

• Increases cure speed on passive and inactive surfaces
• Suitable for low-temperature curing (< 5°C)
• Supplied in aerosol of 150ml
• Manufacturer's part 142479

Loctite SF 7457 142747 is used where increased cure speed of Loctite cyanoacrylate adhesives is required.

It can be applied to the bond before or after assembly. When used pre-applied, its presence can be detected by fluorescence.

• Formulated to provide good on-part life
• Especially suited for post-application on cyanoacrylate adhesives to ensure rapid curing
• Typical applications include: securing wires or coils to PCBs, tamper-proofing adjustable components, mounting stand-offs, edge guides and board stiffeners
• Supplied in a 150ml aerosol can
• Loctite type SF 7457 / 142747

LOCTITE® SF 7701™ is used to make polyolefin and other low energy surfaces suitable for bonding with Loctite cyanoacrylate adhesives.

On such treated surfaces the cured performance of LOCTITE® cyanoacrylate adhesives is generally similar to that described in the TDS for the relevant adhesive. It is only recommended for difficult to bond substrates which include polyethylene, polypropylene, polytetrafluoroethylene (PTFE) and thermoplastic rubber materials.

It is not recommended in assemblies where high peel strength is required.

LOCTITE® SF 7701™ is suitable for use in the assembly of disposable medical devices.

• Clear colourless liquid
• Low viscosity
• Supplied in 473ml container
• Manufacturer's part 2171393

Loctite 1623766 Glue Remover is ideal for the removal of superglue and many other glues from badly bonded objects, stained surfaces, fabric and accidentally bonded fingers. It has a non-drip gel formula and is clean, quick and easy to use.

• Ideal for badly bonded items
• Helps clear up accidental spills
• Removes ink-marker stains
• Frees bonded skin
• Supplied in a 5g tube
• Loctite type 1623766

This transparent, colourless sulfenamide-based, liquid cyanoacrylate cure activator from Loctite contains n-Heptane and is ideal for use where increased cure speed of cyanoacrylate adhesives is required.

Typical examples are post curing of fillets of adhesive in jewellery or decorative part bonding, loudspeaker assembly bonding and coil to ferrite bonding.

• Very low viscosity
• Especially suited for post application to exposed cyanoacrylate adhesive outside the bond line
• Supplied in aerosol of 150ml
• Manufacturer's part 267349

Loctite 770 is a cyanoacrylate primer for making polyolefin and other low energy surfaces suitable for bonding with Loctite cyanoacrylate adhesives. Its use is recommended for difficult to bond substrates like polyethylene, polypropylene, polytetrafluoroethylene (PTFE) and thermoplastic rubber materials.

• Can be applied by spraying, brushing or dipping at ambient temperature
• Presence of primer can be detected by means of a UV inspection lamp (365nm)
• If using with polyolefin and other more active or easier to bond materials, apply the primer to the polyolefin only
• Supplied in 10ml bottles with brush applicator in the lid
• Loctite type 770

Not recommended for use in assemblies where high peel strength is required.

Loctite 770 is a cyanoacrylate primer for making polyolefin and other low energy surfaces suitable for bonding with Loctite cyanoacrylate adhesives. Its use is recommended for difficult to bond substrates like polyethylene, polypropylene, polytetrafluoroethylene (PTFE) and thermoplastic rubber materials.

• Can be applied by spraying, brushing or dipping at ambient temperature
• Presence of primer can be detected by means of a UV inspection lamp (365nm)
• If using with polyolefin and other more active or easier to bond materials, apply the primer to the polyolefin only
• Supplied in 300g container
• Loctite type 770

Note: Not recommended for use in assemblies where high peel strength is required.

Loctite SF 7455 is a colourless, amine-based accelerator used to increase the cure speed of cyanoacrylate adhesives and can be applied before or after the bond to ensure rapid fixturing. Used for securing wires or coils to PCBs, tamper-proofing adjustable components, mounting stand-offs, edge guides, etc, it can also bond dissimilar materials such as metals, glass or ceramics.

• General purpose
• Suitable for all substrates
• Fast fixturing between close fitting parts
• For post-application
• Supplied in aerosol of 150ml
• Manufacturer's part 219992

Loctite SF 7452 is a transparent light amber accelerator for the increased cure speed of cyanoacrylate adhesives. It can be either pre- or post-applied and is especially suited for post-application on cyanoacrylate adhesive to ensure rapid fixturing.

Typical applications include securing wires or coils to PCBs, tamper-proofing adjustable components, mounting stand-offs, edge guides and board stiffeners.

• Cures excess adhesive
• Provides excellent cosmetic appearance avoiding the white discolouration of instant adhesives
• Not recommended on plastics prone to stress cracking
• Supplied in container of 500ml
• Manufacturer's part 2733631

Loctite SF 7455 is used where increased cure speed of Loctite cyanoacrylate adhesives is required. It can be either pre- or post-applied to the bond, but is especially suited for post-application on cyanoacrylate adhesive to ensure rapid fixturing. Typical applications include securing wires or coils to PCBs, tamper-proofing adjustable components, mounting stand-offs, edge guides and board stiffeners.

Loctite SF 7455's typical applications include bonding dissimilar materials such as metals, glass or ceramics and where fast fixturing is required between close fitting parts.

• Medium viscosity
• Low density: SG = 1.0
• High strength
• Working time: 60 minutes
• Fixture time: 180 minutes
• Viscosity 35Pa.s
• Tensile strength: 32N/mm²
• Peel strength: 8N/mm
• Service temperature range: -55 to +120°C
• Colour mix: off-white
• Supplied in a 25ml aerosol
• Loctite type SF 7455

Loctite SF 7455 is used where increased cure speed of Loctite cyanoacrylate adhesives is required. It can be either pre- or post-applied to the bond, but is especially suited for post-application on cyanoacrylate adhesive to ensure rapid fixturing. Typical applications include securing wires or coils to PCBs, tamper-proofing adjustable components, mounting stand-offs, edge guides and board stiffeners.

Loctite SF 7455's typical applications include bonding dissimilar materials such as metals, glass or ceramics and where fast fixturing is required between close fitting parts.

• Medium viscosity
• Low density: SG = 1.0
• High strength
• Working time: 60 minutes
• Fixture time: 180 minutes
• Viscosity 35Pa.s
• Tensile strength: 32N/mm²
• Peel strength: 8N/mm
• Service temperature range: -55 to +120°C
• Colour mix: off-white
• Supplied in a 500ml can
• Loctite type SF 7455

Loctite SF 7240 is designed to promote the curing speed of anaerobic adhesives and sealants without any significant loss of joint strength. It is especially recommended for applications with passive metals or inert surfaces and with large bond gaps.

This product should also be used where the cure temperature is low and is particularly recommended for cure conditions below 15°C.

• Increases cure speed on passive and inactive surfaces
• For large bond gaps
• Supplied in 90ml container
• Manufacturer's part 333369

Loctite SF 7471 is a transparent, yellow to amber liquid activator used where increased cure speed of anaerobic products is required. It is especially recommended for applications with passive metals or inert surfaces and with large bond gaps and when the prevailing temperature is low (<+15 °C).

• Speeds up cure on passive and active surfaces
• Suitable for large bond gaps
• On-part life ≤7 days
• Supplied in 500ml can
• Manufacturer's part 142468

MagmaBond MAG 68 Cyanoacrylate Adhesive Debonder has been specially formulated to release and remove cyanoacrylate adhesives and super glues. It is highly effective as a dismantling solvent and for releasing accidentally bonded skin.

• Readily removes cured adhesive
• Gives a clean surface for rebonding
• Safe for use on most materials except plastics like ABS and polystyrene which are readily attacked by solvents
• Can also be used to release accidentally bonded skin
• Supplied in a 20ml bottle with nozzle applicator
• MagmaBond type MAG 68

Radically reduces the time adhesives and super glues take to cure. Ideal for large gap fills up to 0.4mm and porous material that are ordinarily troublesome to glue. Can be used on MDF, wood, glass, metal and most plastics.

Radically reduces the time adhesives and super glues take to cure. Ideal for large gap fills up to 0.4mm and porous material that are ordinarily troublesome to glue. Can be used on MDF, wood, glass, metal and most plastics.

• Radically reduces the time adhesives and super glues take to cure.
• Assists with large gap fills up to 0.4mm and porous material that ordinarily are troublesome to glue.
• Can be used on MDF, wood, glass, metal and most plastics.
• Model No. SCS300S

The Tesa® 60042 Professional Adhesive Remover 200ml is a spray for easy removal of glue residue from plastic parts, glass and metal surfaces. This quality adhesive remover also evaporates without leaving residues, leaving a pleasant scent.