Strong tubular frame supplied with a range of pins to fit the most common headstock sizes. Once in place, access to all mechanical components at the front of the bike is made easy. Stand folds down for compact storage when not in use. Supplied with width and angle adjustable rubber support pads to quickly and easily use as rear support stand.

• Strong tubular frame supplied with a range of pins to fit the most common headstock sizes.
• Once in place, access to all mechanical components at the front of the bike is made easy.
• Stand folds down for compact storage when not in use.
• Pin Sizes: 12, 15, 16, 18, 24mm.
• Model No. FPS5

Features adjustable pivoting wheel guide, which secures front wheel within chock. Three adjustable heights depending on diameter of wheel. Suitable for wheels with tyre widths 90-130mm and diameters Ø17"-21"(430-535mm). Base can be permanently bolted to the floor (fixings included), and features a detachable upper assembly that can be easily stored and re-attached when required, stabilizing motorcycles without the need for side or centre-stands. Base features lashing strap gap for securing the bike in transport.

• Features adjustable pivoting wheel guide, which secures front wheel within chock.
• Three adjustable heights depending on diameter of wheel.
• Suitable for wheels with tyre widths 90-130mm and diameters Ø17"-21"(430-535mm).
• Base can be permanently bolted to the floor (fixings included).
• Features a detachable upper assembly that can be easily stored and re-attached when required, stabilizing motorcycles without the need for side or centre-stands.
• Base features lashing strap gap for securing the bike in transport.
• Model No. FPS6

Tubular wheel chock supports the front wheel of the motorcycle when in transit or storage. Fully adjustable to fit wheels 15"-21"(380-535mm). Features a pivot clamp which locks the front wheel securely by the motorcycle weight. Chock can be used freestanding or fixed to any hard surface.

• Tubular wheel chock made from square section steel, supports the front wheel of the motorcycle when in transit or storage.
• Fully adjustable to fit wheels Ø15"-21"(380-535mm).
• Minimum/Maximum tyre width: 50-130mm.
• Features a pivot clamp which locks the front wheel securely by the motorcycle weight.
• Chock can be used freestanding or fixed to any hard surface (fixings not included).
• Please note: Motorcycle must also be secured using tie down straps.
• Model No. FPS7

Optional fork cradle support for front paddock stands. Designed to cradle and lift the front forks of a motorcycle for cleaning and storage. Yellow phosphate finish for added corrosion resistance. For safety always ensure that the rear of the bike is supported securely prior to lifting the front end of the motorcycle.

• Optional fork cradle support for front paddock stands.
• Designed to cradle and lift the front forks of a motorcycle for cleaning and storage.
• Yellow phosphate finish for added corrosion resistance.
• For safety always ensure that the rear of the bike is supported securely prior to lifting the front end of the motorcycle.
• Model No. FPSFC

All steel scissor type construction with foot operation and integral hydraulic pump. Unique foot design and safety pins allow use with off-road/trials bikes. Features three locking heights. Support platform with rubber top protects paintwork on bike.

Steel construction with bottle jack style hydraulic unit. Lifting arms suitable for bikes with cradle frames, quads, all terrain vehicles, trikes and vehicle transmissions. Features two mechanical safety locks, lockable in four positions, for supporting the motorcycle over extended periods. Mounted on two fixed wheels and two double castors for manoeuvrability. Can be used with or without the supplied frame supports. Space saving design maximizes garage working area. With a low minimum height of 110mm (200mm with frame supports), it will lift and support the bike through to a maximum height of 400mm (508mm with frame supports). Unlike most other motorcycle lifts, it is possible to remove both wheels, front forks, steering assembly, rear swing arm and suspension units as well as the engine. Can be used anywhere with a hard level floor thus making this suitable for mobile motorcycle mechanics. Ideal for use with the Sealey range of wheel chocks to assist supporting the motorcycle, whilst adjusting the frame supports and securing to the lift.

• Steel construction scissor with bottle jack style power unit.
• Four locking positions for supporting the motorcycle over extended periods on the lift.
• With this lift it is possible to remove both wheels, front forks, steering assembly, rear swing arm and suspension units as well as the engine.
• Benefits from being portable so can be used anywhere with a hard level floor thus making this suitable for mobile motorcycle mechanics.
• Ideal for use with the Sealey range of wheel chocks to assist supporting the motorcycle, whilst adjusting the frame supports and securing to the lift.
• Min./Max. Lift Height (without Frame Supports): 110/400mm.
• Min./Max. Lift Height (with Frame Supports): 210/508mm.
• Maximum Frame Dimensions (W x D): 680 x 360mm.
• Model No. MC4500

Scissor support stand suitable for use either on a motorcycle lift or on the floor. Fitted with ball bearing rollers for smooth lifting and lowering. Raise with sliding T-bar. Supplied with non-slip platform cover for added load security.

All steel construction with a 680kg capacity powered by 230V Electro/Hydraulic lifting system for simple, fast operation. Heavy-duty ramp and platform with removable rear access panel to aid with wheel removal. Supplied with motorcycle front wheel locking attachment for tyre widths between 75-340mm to assist in securing the vehicle. Fitted with multi-position safety lock to prevent accidental lowering. Suitable for use with centre-stand motorcycles or with a rear paddock stand. Can be easily converted to a Mini Tractor, Quadbike lift with the additional side ramps (Model No. MC680EXK).

• Min./Max. Height: 210/1000mm.
• Width: 750mm.
• Length: 2000mm.
• All steel construction with a 680kg capacity.
• 230V Electro/Hydraulic lifting system for simple, fast operation.
• Heavy-duty ramp and platform with removable rear access panel to aid with wheel removal.
• Supplied with motorcycle front wheel locking attachment for tyre widths between 75-340mm to assist in securing the vehicle.
• Fitted with safety lock to prevent accidental lowering.
• Can be easily converted to a Mini Tractor, Quadbike lift with the additional side ramps Model No. MC680EXK.
• Suitable for use with centre-stand motorcycles or with a rear paddock stand.
• This item is heavy. Extra assistance must be provided at the delivery point to help its safe delivery.
• Model No. MC680E

All steel construction four piece ramp extension kit for Model No. MC680E motorcycle lift. The kit consists of two lift table extensions and two additional loading ramps. This converts motorcycle lift into a 2000mm x 1260mm 680kg mini tractor/quadbike or ATV lift. Fitted with automatic anti-roll off devices.

• All steel construction four piece ramp extension kit for Model No. MC680E motorcycle lift.
• Converts motorcycle lift into a 2000mm x 1260mm 680kg mini tractor/quadbike or ATV lift.
• Consists of two lift table extensions and two additional loading ramps.
• Fitted with automatic anti-roll off devices.
• Model No. MC680EXK

Lightweight, folding design with wheels make this workbench mobile and allows compact storage where workshop space is limited. With a working height of 460mm, it is ideal for servicing/maintenance. Additionally the loading ramp doubles as a convenient workshop stool. Suitable for professional workshops, mobile mechanics, enthusiasts, track days or as a display table in showrooms.

Quickly and safely lifts and stabilises front or back of a motorcycle with a traditional style double cradle frame design that has no engine, transmission or exhaust protrusions. Features height adjustment and soft PVC sheath for protection to underside of bike. Design of stand allows easy wheel maintenance and removal of front or rear wheel.

Powder-coated pressed steel frame, to ensure strength and durability. Ideal for use with off-road/trials bikes to easily lift the bike when needing to perform maintenance, services or cleaning. Simple, one foot, step-and-lift mechanism means the bike can be instantly raised in one motion. For added safety, features an ‘over centre’ locking toggle linkage to mechanically lock the lift at full height to prevent accidental lowering, also fitted with hydraulic dampener for controlled descent.

Motorcycle dolly holds a single motorcycle with a side stand, weighing up to 565kg. Easy to manoeuvre around the workshop or garage. Front and rear lever operated wedge gates allow for easy loading and unloading to the 2000 x 200 x 50mm (L x W x H) loading track. Includes a five-position side stand platform to fit varied length side stand, front/rear steel pins to keep the motorcycle on the dolly during moving, and smooth rolling dual castor wheels.

This motorcycle moving dolly can be used to manoeuvre motorcycles (up to 220kg vehicle weight) with centre-stands and is perfect for places where space is restrictive. The centre stand locates on the 4mm thick hardened steel plate and the 360 degree castors allow the bike to be moved in any direction. Features a hand operated built-in-brake mechanism which is ideal for workshop, showroom and home garage use.

• Use to manoeuvre motorcycles (up to 220kg vehicle weight) with centre-stands.
• Perfect for places where space is restrictive.
• The dolly is made from 4mm thick hardened steel plate.
• Covered with anti-slip rubber pad.
• Foot operated built-in brake mechanism.
• Ideal for workshop, showroom and home garage use.
• Model No. MS0651