A fully assembled pan-tilt bracket that comes complete with 2x micro servos (SG-90 or SG-92 type). The device can rotate approximately 180° from side to side and can tilt up and down by approximately 150°. There is also a 38 x 36mm space on the bracket to enable the mounting of other equipment such as a camera or sensor. Because the motors are plain analog servos, any microcontroller or driver may be used for control. Perfect for providing motion in any project.

• Compatible with the Arduino Servo library

*Customers looking to resell on eBay or Amazon should contact Adafruit directly.

The Arduino 4 Relays shield is designed as a solution for driving those high power loads that cannot be driven by Arduino's digital IOs due to current and voltage limits. The shield features 4x relays, with each relay providing 2 pole changeover contacts (NO and NC). The 2 changeover contacts have been put in parallel in order to increase output current limits. The relays are controlled by the following Arduino board pins: Relay 1 = Arduino pin 4 Relay 2 = Arduino pin 7 Relay 3 = Arduino pin 8 Relay 4 = Arduino pin12

• Compatible with all Arduino boards, 5V and 3.3V
• 4x Status LEDs
• Power provided by base board
• Operating voltage 5V
• Maximum switching capacity 60W
• 6x TinkerKit IO interfaces

The Eagle files can be downloaded here.

The schematic can be downloadedhere.

The Arduino Motor Shield is based on the L298, which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your Arduino board, controlling the speed and direction of each one independently. You can also measure the current absorption of each motor, among other features. The shield is TinkerKit compatible, which means you can quickly create projects by plugging TinkerKit modules to the board.

• Operating Voltage 5V to 12V
• Motor controller L298P, Drives 2 DC motors or 1 stepper motor
• Max current 2A per channel or 4A max (with external power supply)
• Current sensing 1.65V/A
• Free running stop and brake function

The Arduino Relay Shield from Seeed Studio gives you 4 relays that will switch 7A at 35V DC each, easily enough for most applications. Screw terminals are provided for the connections to the device being switched and an LED indicator shows the status of each relay's normally open (NO) contacts. Your Arduino can control the board via 4 digital output pins giving you the opportunity to control multiple relay boards. PCBs with high voltage electricity can be dangerous, please take precautions to prevent shocks and short circuits. It is recommended that you apply two layers of insulating tape to the top of the Arduino's USB connector to prevent short circuits.

• 4 x relays with 1 x NO and 1 x NC contacts each
• 4 digital outputs used for each board
• LED indicators on each relay
• Screw terminals for switched devices

Seeed provide technical documentation, example projects and software libraries on their product pages. if you require this information please visit this product's page.

The Energy Shield from Seeed Studio is a highly adaptable power system, capable of accepting power from solar cells, and via micro-USB. Your Li-ion battery will provide power (up to 600mA) when no other supply is connected and it will be charged when external power is available. Fitted with an On/Off switch. This is a must for your next Arduino portable or off grid project.

• Energy Shield intelligently charges your Li-ion batteries
• Also powers your Arduino while charging
• Charges from solar cells

Seeed provide technical documentation, example projects and software libraries on their product pages. if you require this information please visit this product's page.

A kit of parts that assembles into an I/O shield designed for use with Arduino Uno, Arduino Mega and Arduino Due boards. When assembled the shield can be used as a general input/output shield for a connected Arduino board. All components required are provided for assembly and full illustrated instructions are supplied.

• Indicator LEDs for relay outputs and digital inputs
• 6x Relay outputs
• 6x Analog inputs
• 6x Digital inputs
• Downloadable example sketch and library available
• Stackable design can be stacked with other shields
• Large user community

Please note: This is a self-assembly kit and requires soldering.

A kit of parts that assembles into a motor and power shield designed for use with Arduino Uno, Arduino Mega and Arduino Due boards. When assembled the shield can be used to drive relays, solenoids, DC and stepper motors. All components required are provided for assembly and full illustrated instructions are supplied.

• 2x Channels
• Choose between external or internal power supply
• Based on the dual full bridge driver L298P
• Downloadable example sketch and library available
• Stackable design can be stacked with other shields
• Large user community

Please note: This is a self-assembly kit and requires soldering.