The DAC08CSZ 8-bit monolithic digital-to-analog converter provides very high speed performance coupled with low cost and outstanding applications flexibility.

DAC08CSZ applications include 8-bit, 1µs A/D converter, servo motor and pen driver, waveform generator, audio encoder and attenuator, analog meter driver, programmable power supply, LCD display driver, high speed modem, and other applications where low cost, high speed and complete input/output versatility are required.

• 16-lead SOIC package
• Fast settling output current: 85ns
• Full-scale current pre-matched to ±1 LSB
• Direct interface to TTL, CMOS, ECL, HTL, PMOS
• Nonlinearity to 0.1% maximum over temperature range
• High output impedance and compliance: -10V to +18V
• Complementary current outputs
• Wide range multiplying capability: 1 MHz bandwidth
• Low FS current drift: ±10 ppm/°C
• Wide power supply range: ±4.5V to ±18V
• Low power consumption: 33mW at ±5V
• Low cost
• Temperature range: -40°C to +85°C
• Analog Devices type DAC08CSZ

Due to Global supply chain disruptions, we are unable to supply lead times for quantities above our current stock holding. For further delivery information please contact our sales team: sales.support@rapidonline.com

This Analog to Digital Converter (ADC) is a CMOS, 18-bit, serial output, integrating device that features a multi-slope integration that enables operation up to 100 conversions per second and higher resolution conversions in less time than standard integrating ADCs. Communication is via a 4-wire serial interface that easily connects to all common microprocessors. Four serially programmed digital outputs can be used to control an external multiplexer or programmable-gain amplifier. High resolution, compact size and low power mean these devices are ideal for use in transducers, data loggers, weighing scales, data acquisition systems and panel meters, battery-powered instruments and industrial process control.

• Up to 100 conversions per second
• 50/60Hz Rejection circuitry
• Low supply current
• ±0.006% FSR accuracy at 16 conv/sec
• Low conversion noise
• Twos-complement output coding simplifies bipolar measurement
• Through-hole DIL-24 package

The DAC0800 series are monolithic 8-bit high-speed current-output digital-to-analogue convertors with 8-Bit resolution and 1 channel. Features include fast settling output current, complementary current outputs, interface directly with TTL, CMOS, PMOS, etc., low power, low cost.

• Parallel interface
• 4.5 to 18V Supply voltage
• 2.5mA Supply current
• 33mW Power
• 0.1% Nonlinearity error
• 100ns Settling time
• 0°C to +70°C
• DIL-16 Case

The WAGO Isolation Amplifier is used to convert, amplify, filter and electrically isolate analog standard signals. The device has a 3-way isolation with a 2.5kV test voltage. DIP switches accessible from the side can be used to configure the signals in both input and output. In addition to standard signals, bipolar (± 10V, ± 20mA) and 0 to 30V signals can also be set on the input side. The analog output supports standard unipolar signals. In addition, the devices can be configured using FDT/DTM software. The software offers additional setting options such as special input and output signal combinations with intermediate values or inversion of the analog output. Measurement range switching is calibrated. A digital switching output is available that can also be configured using software.

The device is supplied with 24VDC, which can be commoned using lateral push-in type jumper bars in a quick and cost effective way. A green LED on the front panel indicates normal operation. The isolation amplifier meets the requirements for safe isolation of inpu

The WAGO Universal Isolation Amplifier is a high quality converter with which measurement range switching is calibrated. The device requires DC 24V supply voltage and can be quickly and economically bridged via the side jumper bar. A green LED on the front of indicates normal operation. Configuration via DIP switch.

The WAGO Frequency Measuring Transducer has a frequency that collects 0.1Hz to 120 kHz signals from NAMUR, NPN or PNP sensors and converts the frequencies into analogue standard signals. Safe 3-way isolation with 2.5kV test voltage to EN 61140.