www.eleinmec.com

Capacitors
By John Hewes

Capacitors store electric charge.  They are used with resistors in timing circuits because it takes time for a capacitor to fill with charge.  They are also used in filter circuits because capacitors easily pass AC (changing) signals but they block DC (constant) signals.

Capacitor Values

This is a measure of a capacitor's ability to store charge.  A large capacitance means that more charge can be stored.  Capacitance is measured in farads, symbol F.  However 1F is very large, so prefixes are used to show the smaller values.

Three prefixes (multipliers) are used, μ (micro), n (nano) and p (pico):

There are many types of capacitor but they can be split into two groups, polarised (for large values, 1μF or more) and unpolarised (for small values, up to 1μF).  Each group has its own circuit symbol.

Polarised Capacitors

Electrolytic Capacitors
Polarised Capacitor Circuit Symbol
   

Electrolytic capacitors are polarised and they must be connected the correct way round - at least one of their leads will be marked + or -.  They are not damaged by heat when soldering.

There are two designs of electrolytic capacitors; axial where the leads are attached to each end (left of figure 1) and radial where both leads are at the same end (right of figure 1).  Radial capacitors tend to be a little smaller and they stand upright on the circuit board.

Figure 1: Electrolytic capacitors

It is easy to find the value of electrolytic capacitors because they are clearly printed with their capacitance and voltage rating. The voltage rating can be quite low (6V for example) and it should always be checked when selecting an electrolytic capacitor.  If the circuit parts list does not specify a voltage, choose a capacitor with a rating which is greater than the circuit's power supply voltage.  25V is a sensible minimum for most circuits.

Tantalum Bead Capacitors

Tantalum bead capacitors are polarised and have low voltage ratings like electrolytic capacitors.  They are expensive but very small, so they are used where a large capacitance is needed in a small size.

Figure 2: Tantalum bead capacitors

Modern tantalum bead capacitors are printed with their capacitance and voltage in full.  However, older ones use a colour-code system which has two stripes (for the two digits) and a spot of colour for the number of zeros to give the value in μF.  The standard capacitor colour code is used (see later in this article), but for the spot, grey is used to mean x0.01 and white means x0.1 so that values of less than 10μF can be shown.  A third colour stripe near the leads shows the working voltage (yellow 6.3V, black 10V, green 16V, blue 20V, grey 25V, white 30V, pink 35V).  Here are some examples:

Unpolarised Capacitors

Unpolarised Capacitor Circuit Symbol
   

Small value capacitors are unpolarised and may be connected either way round.  They are not damaged by heat when soldering, except for one unusual type (polystyrene).  They have high voltage ratings of at least 50V, usually 250V or so.

Figure 3: Various unpolarised capacitors

It can be difficult to find the values of these small capacitors because there are many types of them and several different labelling systems!

Many small value capacitors have their value printed but without a multiplier, so you need to use experience to work out what the multiplier should be:

For example, 0.1 means 0.1μF = 100nF.

Sometimes the multiplier is used in place of the decimal point:

For example, 4n7 means 4.7nF.

Polystyrene Capacitors

This type, shown on the right of figure 3, is rarely used now.  Their value (in pF) is normally printed without units. Polystyrene capacitors can be damaged by heat when soldering (it melts the polystyrene!) so you should use a heatsink (such as a crocodile clip).  Clip the heatsink to the lead between the capacitor and the joint.

Capacitor Number Code

A number code is often used on small capacitors where printing is difficult:

Here are some examples:

102   means 1000pF = 1nF   (not 102pF!)

472J means 4700pF = 4.7nF (J means 5% tolerance)

Capacitor Colour Code

A colour code was used on polyester capacitors for many years.  It is now obsolete, but of course there are many still around.  The colours should be read like the resistor code, the top three colour bands giving the value in pF.  Ignore the 4th band (tolerance) and 5th band (voltage rating).  Note that there are no gaps between the colour bands, so two identical bands actually appear as one wide band.

The table below shows the meaning of each colour for each of the bands.

Colour Band 1
1st Digit
   Band 2
2nd Digit
   Band 3
Multiplier
Black 0 0 x 1
Brown 1 1 x 10
Red 2 2 x 100
Orange 3 3 x 1,000
Yellow 4 4 x 10,000
Green 5 5 x 100,000
Blue 6 6 x 1,000,000
Violet 7 7 -
Grey 8 8 -
White 9 9 -

Figure 4 shows a few examples of the capacitor colour code.

Figure 4: Some examples of the capacitor colour code

Article Information
Source: Electronics in Meccano - www.eleinmec.com
Topic: Components Explained | Created: 19/05/2002 | Last modified: 13/02/2007

Top of Page | Homepage | About | Search | Topics | Features | Circuits Shop | yourEiM

© 1998 - 2024 Tim Surtell